参数资料
| 型号： | MAX8751ETJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/27页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR CCFL INV 32-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | CCFL 控制器 |
| 频率： | 30 ~ 80 kHz |
| 电流 - 电源： | 3.2mA |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Fixed-Frequency, Full-Bridge CCFL
Inverter Controller
mode, at the beginning of the positive half cycle, NH1
and NL2 turn on and the primary current starts ramping
up. The controller turns off NH1 as the primary current
reaches its peak value. The primary current continues to
flow in the same direction, which forward biases the
body diode of NL1, ramping down the primary current.
When the primary current reaches zero, NL2 is turned off
and NH2 is turned on, starting the negative half cycle.
Lamp-Current Regulation
The MAX8751 uses a lamp-current control loop to regu-
late the current delivered to the CCFL. The heart of the
control loop is a transconductance error amplifier in
Figure 2. The AC lamp current is sensed with a sense
resistor connected in series with the low-voltage termi-
nal of the lamp. The voltage across this resistor is fed to
the IFB input and is internally full-wave rectified. The
transconductance error amplifier compares the recti-
fied IFB voltage with a 790mV (typ) internal reference to
generate an error current. The error current charges
and discharges a capacitor connected between the
error amplifier’s output (COMP) and ground to create
an error voltage (V COMP ). V COMP is then compared
with an internal ramp signal to control the high-side
MOSFET switch on-time (t ON ).
Transformer Secondary Voltage Limiting
The MAX8751 reduces the voltage stress on the trans-
former’s secondary winding by limiting the secondary
voltage during startup and open-lamp condition. The AC
voltage across the transformer secondary winding is
sensed through a capacitive voltage-divider. The volt-
age across the low-side capacitor of the divider is fed to
the VFB pin of the MAX8751. An overvoltage compara-
tor compares the VFB voltage with 2.25V (typ) internal
threshold. If the sensed voltage exceeds the overvolt-
age threshold, the MAX8751 turns on an internal
1200μA current source, which discharges the COMP
capacitor. The high-side MOSFET’s on-time shortens as
the COMP voltage decreases, hence reducing the
transformer’s secondary peak voltage below the thresh-
old set by the capacitive voltage-divider.
Lamp Startup
A CCFL is a gas-discharge lamp that is normally driven
in the avalanche mode. To start ionization in a nonion-
ized lamp, the applied voltage (striking voltage) must
be increased to the level required for the start of
avalanche. For example, the normal running voltage of
a typical CCFL is approximately 650V RMS , but the strik-
ing voltage can be as high as 1800V RMS .
The MAX8751 ’s unique resonant startup method
ensures reliable striking. Before the lamp is ionized, the
lamp impedance is infinite. The transformer secondary
leakage inductance and the high-voltage parallel
capacitor determine the unloaded resonant frequency.
Since the unloaded resonant circuit has a high Q, the
inverter keeps increasing the secondary voltage until
either the lamp is struck or the controller activates the
secondary overvoltage protection.
Upon power-up, V COMP slowly rises, increasing the
duty cycle of the high-side MOSFET switches and pro-
viding a measure of soft-start. In addition, the MAX8751
pulls up V FB to the overvoltage threshold (2.25V, typ)
immediately after the device is enabled. The DC volt-
age on V FB is gradually discharged through an internal
resistor during startup. This feature is equivalent to
slowly raising the overvoltage threshold during startup,
so it further improves the soft-start behavior. The
MAX8751 automatically switches over to constant-fre-
quency operation after the IFB voltage rises above
open-lamp threshold.
Feed-Forward Control and Dropout
Operation
The MAX8751 is designed to maintain tight control of
the lamp current under all transient conditions. The
feed-forward control instantaneously adjusts the on-
time for changes in input voltage (V IN ). This feature pro-
vides immunity to input-voltage variations and simplifies
loop compensation over wide-input voltage ranges. The
feed-forward control also improves the line regulation
for short DPWM on-times and makes startup transients
less dependent on the input voltage.
Feed-forward control is implemented by increasing the
internal voltage ramp rate for higher V IN . This has the
effect of varying t ON as a function of the input voltage
while maintaining almost the same signal levels at
V COMP . Since the required voltage change across the
compensation capacitor is minimal, the controller ’s
response to input voltage change is essentially
instantaneous.
DPWM Dimming Control
The MAX8751 controls the brightness of the CCFL by
“chopping” the lamp current on and off using a low-fre-
quency (between 80Hz and 300Hz) DPWM signal
either from the internal oscillator or from an external sig-
nal source. In the DPWM operation, COMP controls the
rise and fall of the lamp current. At the beginning of the
DPWM on-cycle, the lamp current is zero; V COMP linear-
ly rises due to charging from transconductance error
amplifier, and t ON increases gradually, increasing the
lamp current slowly, providing soft-start. The lamp cur-
rent stabilizes after it reaches the regulation point. At
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8752ETA+T | IC DC-DC CONV TFT LCD 8-TDFN |
| MAX8753ETI+T | IC DC-DC CONV TFT LCD 28TQFN |
| MAX8756ETI+T | IC CNTRL DUAL PS 28-TQFN |
| MAX8758ETG+T | IC REG STEP UP 24-TQFN |
| MAX8759ETI+T | IC CNTRL CCFL BACKLIGHT 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8751EVKIT | 功能描述:电源管理IC开发工具 MAX8751 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX8752ESA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX8752ETA | 制造商:Maxim Integrated Products 功能描述:TFT LCD STEP-UP DC-DC CONVERTER - Rail/Tube |
| MAX8752ETA+ | 制造商:Maxim Integrated Products 功能描述:TFT LCD DC-DC CNVRTR 8TDFN EP - Rail/Tube |
| MAX8752ETA+T | 功能描述:LCD 驱动器 TFT LCD Step-Up DC/DC Converter RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。