- 您现在的位置：买卖IC网 > PDF目录16560 > MAX8819CETI+T (Maxim Integrated Products)IC PMIC W/INT CHARGER 28TQFN-EP PDF资料下载
参数资料
| 型号： | MAX8819CETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/29页 |
| 文件大小： | 0K |
| 描述： | IC PMIC W/INT CHARGER 28TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 手持/移动设备 |
| 电源电压： | 4.1 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
PMIC with Integrated Chargers and Smart
Power Selector in a 4mm x 4mm TQFN
In addition to charging the battery, the IC supplies
power to the system through the SYS output. The
charging current is provided from SYS so that the set
input current limit controls the total SYS current, this is
the sum of the system load current and the battery-
charging current.
In some instances, there may not be enough DC input
current to supply peak system loads. The Smart Power
Selector circuitry offers flexible power distribution from
an AC-to-DC adapter or USB source to the battery and
system load. The battery is charged with any available
power not used by the system load. If a system load
peak exceeds the input current limit, supplemental cur-
rent is taken from the battery. Thermal limiting prevents
overheating by reducing power drawn from the input
source. In the past, it might have been necessary to
reduce system functionality to limit current drain when a
USB source is connected. However, with the
MAX8819_, this is no longer the case. When the DC or
USB source hits its limit, the battery supplies supple-
mental current to maintain the load.
The IC features overvoltage protection. Part of this protec-
tion is a 4.35V (MAX8819A/MAX8819C) or 5.3V
(MAX8819B) voltage limiter at SYS. If DC exceeds the
overvoltage threshold of 5.88V (V OVLO_DC ), the input lim-
iter disconnects SYS from DC, but battery-powered oper-
ation of all regulators is still allowed.
Input Limiter
The Smart Power Selector seamlessly distributes power
between the current-limited external input (DC), the bat-
tery (BAT), and the system load (SYS). The basic func-
tions performed are:
With both an external power supply (DC) and battery
(BAT) connected:
? When the system load requirements are less than
the input current limit, the battery is charged with
residual power from the input.
? When the system load requirements exceed the
input current limit, the battery supplies supplemental
current to the load through the internal system load
switch.
? When the battery is connected and there is no exter-
nal power input, the system (SYS) is powered from
A thermal-limiting circuit reduces the battery charge
rate and external power source current to prevent the
MAX8819_ from overheating.
System Load Switch
An internal 70m Ω MOSFET connects SYS to BAT when
no voltage source is available at DC. When an external
source is detected at DC, this switch opens and SYS is
powered from the valid input source through the Smart
Power Selector.
When the system load requirements exceed the input
current limit, the battery supplies supplemental current
to the load through the internal system load switch. If
the system load continuously exceeds the input current
limit, the battery does not charge, even though external
power is connected. This is not expected to occur in
most cases because high loads usually occur only in
short peaks. During these peaks, battery energy is
used, but at all other times the battery charges.
DC Power Input (DC, DLIM1, DLIM2)
DC is a current-limited power input that supplies the
system (SYS) up to 1A. The DC to SYS switch is a linear
regulator designed to operate in dropout. This linear
regulator prevents the SYS voltage from exceeding
5.3V for the MAX8819B or 4.35V for the MAX8819A/
MAX8819C. As shown in Table 1, DC supports four dif-
ferent current limits that are set with the DLIM1 and
DLIM2 digital inputs. These current limits are ideally suit-
ed for use with AC-to-DC wall adapters and USB power.
The operating voltage range for DC is 4.1V to 5.5V, but it
can tolerate up to 6V without damage. When the DC
input voltage is below the undervoltage threshold (4V), it
is considered invalid. When the DC voltage is below the
battery voltage it is considered invalid. The DC power
input is disconnected when the DC voltage is invalid.
Bypass DC to ground with at least a 4.7μF capacitor.
Four current settings are provided based upon the set-
tings of DLIM1 and DLIM2, see Table 1. DLIM1 and
DLIM2 are deglitched. This deglitching prevents the
problem of major carry transitions momentarily entering
the suspend state.
Table 1. DC Current-Limit Settings
the battery.
? When an external power input is connected and
there is no battery, the system (SYS) is powered
from the external power input.
DLIM1
0
0
1
1
DLIM2
0
1
0
1
DC I LIM (mA)
1000
475
95
Suspend
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX749ESA+T | IC SUPPLY LCD BIAS ADJ 8-SOIC |
| RSA06DRSN-S288 | CONN EDGECARD 12POS .125 EXTEND |
| H3CCS-6406M | IDC CABLE - HKC64S/AE64M/HKC64S |
| UPC3218GV-EVAL | EVAL BOARD FOR UPC3218GV |
| M2MXH-2020K | IDC CABLE - MDM20H/MC20F/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8819DETI+ | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX8819DETI+T | 功能描述:PMIC 解决方案 PMIC w/Charger & Smart Power Selector RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX881REUB | 功能描述:PMIC 解决方案 Bias Supply w/Power OK for GaAsFET PA RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX881REUB+ | 功能描述:PMIC 解决方案 Bias Supply w/Power OK for GaAsFET PA RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX881REUB+T | 功能描述:PMIC 解决方案 Bias Supply w/Power OK for GaAsFET PA RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。