- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8900DEWV+T (Maxim Integrated Products)IC LI BATTERY CHARGER 1.2A WLP PDF资料下载
参数资料
| 型号： | MAX8900DEWV+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/35页 |
| 文件大小： | 0K |
| 描述： | IC LI BATTERY CHARGER 1.2A WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 3.4 V ~ 6.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 30-WFBGA，WLBGA |
| 供应商设备封装： | 30-WLP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页
MAX8900A/MAX8900B/MAX8900C
1.2A Switch-Mode Li+ Chargers with ±22V Input
Rating and JEITA Battery Temperature Monitoring
PVL and AVL Regulator
PVL is a 5V linear regulator that the MAX8900_ uses to
power the gate drivers for its step-down charger. PVL
also charges the BST capacitor. The PVL linear regulator
is on when CEN is low, V IN is greater than ~2V, and V IN
is above V BAT by the V IN2BAT threshold, otherwise it is
off. Bypass PVL with a 1 F F ceramic capacitor to GND.
Powering external loads from PVL is not recommended.
As shown in Figure 3, AVL is a filtered output from the
PVL linear regulator that the MAX8900_ uses to power its
internal analog circuits. The filter consists of an internal
12.5 I resistor and the AVL external bypass capacitor
(0.1 F F). This filter creates a 127kHz lowpass filter that
cleans the 3.25MHz switching noise from the analog por-
tions of the MAX8900_. Connect a 0.1 F F ceramic capaci-
tor from AVL to GND. Powering external loads with AVL
is not recommended.
Charge Status Outputs (3 Pin)
STAT1, STAT2, and STAT3 are open-drain outputs that
indicate the status of the MAX8900B/MAX8900C as
shown in Table 3.
When the status outputs are used to communicate with a
F P, pull them up to the system logic voltage (V LOGIC ) to
create a signal that has a logic-high and logic-low state that
the F P can easily interpret (Figure 2). Since more than one
status signal may change when the MAX8900B/MAX8900C
changes states, the F P must implement a deglitching
routine for the interpretation of the status signals.
Table 3. 3-Pin Status Output Truth Table
When the status outputs are used to drive LED indicators,
a series resistor should limit the LED current to be less
than 30mA (Figure 1). The STAT1 and STAT2 typical pull-
down resistance is 25 I and the absolute maximum rating
is +30V. This +30V rating allows IN to be used to bias
STAT1 and STAT2. The STAT3 typical pulldown resis-
tance is 10 I and the absolute maximum rating is +6V.
Charge Status Outputs (2 Pin + > T4)
STAT1 and STAT2 are open-drain outputs that indicate
the status of the MAX8900A as shown in Table 4.
When the status outputs are used to communicate with a
F P, pull them up to the system logic voltage (V LOGIC ) to
create a signal that has a logic-high and logic-low state
that the F P can easily interpret (Figure 2). Since more
than one status signal may change when the MAX8900A
changes states, the F P must implement a deglitching
routine for the interpretation of the status signals.
When the status outputs are used to drive LED indica-
tors, a series resistor should limit the LED current to
be less than 30mA (Figure 1). Note that the STAT1 and
STAT2 typical pulldown resistance is 25 I and the abso-
lute maximum rating is +30V. This +30V rating allows IN
to be used to bias STAT1 and STAT2.
STAT3 pulls low when the battery temperature moni-
tor detects that the battery temperature is greater than
the T4 threshold, otherwise, STAT3 is high impedance.
Some systems may want to reduce the battery loading
when STAT3 pulls low to prevent the battery from getting
excessively hot.
STAT1
0
STAT2
0
STAT3
0
INDICATION
Battery cold (THM < T1)
Table 4. 2-Pin Status Output Truth Table
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
V IN > V OVLO
Charging (dead-battery state or
dead battery + prequalification
state or prequalification state or
fast-charge state)
Battery hot (THM >T4)
Done state
Undefined. This
state does not occur.
Timer fault
V IN < V UVLO or CEN = 1 or
V IN < (V BAT + V IN2BAT ) or
thermal shutdown
STAT1
0
0
1
1
STAT2
0
1
0
1
INDICATION
Undefined. This does not occur
when the MAX8900_ is powered.
Charging (dead-battery state or
dead battery + prequalification state
or prequalification state or fast-
charge state)
Timer fault or V IN > V OVLO or bat-
tery cold (THM < T1) or battery hot
(THM > T4)
Done state or CEN = 1 or V IN <
V UVLO or V IN < (V BAT + V IN2BAT ) or
thermal shutdown
Note: STAT1, STAT2, and STAT3 are open-drain outputs. “0”
indicates that the output device is pulling low. “1” indicates
that the output is high impedance.
Maxim Integrated
Note: STAT1 and STAT2 are open-drain outputs. “0” indicates
that the output device is pulling low. “1” indicates that the out-
put is high impedance.
27
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8902AATA+T | IC REG LDO ADJ .5A 8TDFN |
| MAX8903DETI+ | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| MAX8903GETI+ | IC DC-DC CHARGER LI+ 2A 28TQFN |
| MAX890LESA | IC SW MOSFET PWR PCH HSIDE 8SOIC |
| MAX8922LETB+T | IC BATTERY CHARGER SGL 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8901AETA+ | 制造商:Maxim Integrated Products 功能描述:HIGHEST EFFICIENCY SUPPLY 8TDFN EP - Rail/Tube |
| MAX8901AETA+T | 功能描述:LED照明驱动器 Supply for 2 to 6 Series WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8901BETA+ | 制造商:Maxim Integrated Products 功能描述:HIGHEST EFFICIENCY SUPPLY FOR 2 TO 6 SERIES WLEDS IN A - Rail/Tube |
| MAX8901BETA+CAR | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8901BETA+T | 功能描述:LED照明驱动器 Supply for 2 to 6 Series WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。