- 您现在的位置：买卖IC网 > PDF目录1850 > MAX8900DEWV+T (Maxim Integrated Products)IC LI BATTERY CHARGER 1.2A WLP PDF资料下载
参数资料
| 型号： | MAX8900DEWV+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/35页 |
| 文件大小： | 0K |
| 描述： | IC LI BATTERY CHARGER 1.2A WLP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 3.4 V ~ 6.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 30-WFBGA，WLBGA |
| 供应商设备封装： | 30-WLP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页
MAX8900A/MAX8900B/MAX8900C
1.2A Switch-Mode Li+ Chargers with ±22V Input
Rating and JEITA Battery Temperature Monitoring
R IN = 2 ×
L PAR =
impedance), the voltage spike could be twice that of
the nominal source voltage. In other words, a 6V source
with a high-Q LC tank circuit in the cabling can result in
a voltage spike as high as 12V. The MAX8900_’s high
input absolute maximum voltage rating of +22V to -22V
eliminates any concerns about the voltage spikes due to
inductive kicking for many applications.
In the event that an application may see a high-Q LC
tank circuit in the cabling for a supply that is > +11V, a
resistor (R IN ) must be added in series with C IN to reduce
the Q of the tank circuit. The resistor value can be found
experimentally by assuming the parasitic inductance
(L PAR ) of the input cabling is 1 F H/m, then use the follow-
ing equation give a good starting value for R IN :
L PAR
C IN
An alternative method for estimating L PAR is to measure
the frequency of the input voltage spike ringing and then
calculate L PAR from the following equation.
1
( 2 × π × f R ) × C IN
Overvoltage and Reverse Input Voltage Protection
The MAX8900_ provides for a +22V absolute maximum
positive input voltage and a -22V absolute maximum
negative input voltage. Excursions to the absolute maxi-
mum voltage levels should be on a transient basis only,
but can be withstood by the MAX8900_ indefinitely.
Situations that typically require extended input voltage
ratings include but are not limited to the following:
U Inductive kick
U Charge source failure
U Power surge
U Improperly wired wall adapter
U Improperly set universal wall adapter
U Wall adapter with the correct plug, but wrong voltage
U Home-built computer with USB wiring harness con-
nected backwards (negative voltage)
U USB connector failure
U Excessive ripple voltage on a switch-mode wall charger
Maxim Integrated
U USB powered hub that is powered by a wall charger
(typically through a barrel connector) that has any of
the aforementioned issues
U Unregulated charger (passively regulated by the
turns ratio of the magnetic’s turns ratio)
U Automotive environment (9V, 12V, any of the afore-
mentioned in reverse).
PCB Layout
The MAX8900_ WLP package and bump configuration
allows for a small-size low-cost PCB design. Figures 3
and 14 show that the MAX8900_ package’s 30 bumps are
combined into 18 functional nodes. The bump configura-
tion places all like nodes adjacent to each other to mini-
mize the area required for routing. The bump configuration
also allows for a layout that does not use any vias within the
WLP bump matrix (i.e., no micro vias). To utilize this no via
layout, CEN is left unconnected and the STAT3 pin is not
used (2-pin status version).
Figure 15 shows the recommended land pattern for the
MAX8900_. Figure 16 shows the cross section of the
MAX8900_’s bump with detail of the under-bump metal
(UBM). The diameter of each pad in the land pattern is
close to the diameter of the UBM. This land pattern to UBM
relationship is important to get the proper reflow of each
solder bump.
Underfill is not necessary for the MAX8900_’s package to
pass the JESD22-B111 Board Level Drop Test Method for
Handheld Electronic Products. JESD22-B111 covers end
applications such as cell phones, PDAs, cameras, and
other products that are more prone to being dropped dur-
ing their lifetime due to their size and weight. Please con-
sider using underfill for applications that require higher reli-
ability than what is covered in the JESD22-B111 standard.
Careful printed circuit layout is important for minimizing
ground bounce and noise. Figure 14 is an example layout
of the critical power components for the MAX8900_. The
arrangement of the components that are not shown in
Figure 14 is less critical. Refer to the MAX8900 Evaluation
Kit for a complete PCB layout example. Use the following
list of guidelines in addition to Application Note 1891:
maximintegrated.com/ucsp ) to layout the MAX8900_
PCB.
31
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8902AATA+T | IC REG LDO ADJ .5A 8TDFN |
| MAX8903DETI+ | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| MAX8903GETI+ | IC DC-DC CHARGER LI+ 2A 28TQFN |
| MAX890LESA | IC SW MOSFET PWR PCH HSIDE 8SOIC |
| MAX8922LETB+T | IC BATTERY CHARGER SGL 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8901AETA+ | 制造商:Maxim Integrated Products 功能描述:HIGHEST EFFICIENCY SUPPLY 8TDFN EP - Rail/Tube |
| MAX8901AETA+T | 功能描述:LED照明驱动器 Supply for 2 to 6 Series WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8901BETA+ | 制造商:Maxim Integrated Products 功能描述:HIGHEST EFFICIENCY SUPPLY FOR 2 TO 6 SERIES WLEDS IN A - Rail/Tube |
| MAX8901BETA+CAR | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX8901BETA+T | 功能描述:LED照明驱动器 Supply for 2 to 6 Series WLEDs RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。