- 您现在的位置：买卖IC网 > PDF目录1946 > MAX9249GCM/V+ (Maxim Integrated Products)IC SERIALIZER GMSL LVDS 48TQFP PDF资料下载
参数资料
| 型号： | MAX9249GCM/V+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/36页 |
| 文件大小： | 0K |
| 描述： | IC SERIALIZER GMSL LVDS 48TQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 250 |
| 功能： | 串行器 |
| 数据速率： | 2.5Gbs |
| 输入类型： | LVDS |
| 输出类型： | 串行 |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-TQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
______________________________________________________________________________________ 27
MAX9249
Gigabit Multimedia Serial Link
Serializer with LVDS System Interface
Figure 24. State Diagram, CDS = High (Camera Application)
Case 4: Remote Side in Sleep Mode
After power-up or when PWDN transitions from low to
high, the remote device (GMSL deserializer) starts up in
sleep mode. The high-speed link establishes automati-
cally after MAX9249 powers up with a stable RXCLKIN_
and sends a wake-up signal to the GMSL deserializer.
Use this mode in applications where the GMSL deserial-
izer powers up before the MAX9249.
Image-Sensing Applications
For image-sensing applications, connect the FC to the
GMSL deserializer and set CDS = high for both the
MAX9249 and GMSL deserializer. The GMSL deserial-
izer powers up normally (SLEEP = 0) and continuously
tries to lock to a valid serial input. Table 9 summarizes
both startup cases, based on the state of the MAX9249
AUTOS pin.
Case 1: Autostart Mode
After power-up, or when PWDN transitions from low to
high, the MAX9249 locks to a stable RXCLKIN_ and
sends the high-speed data to the GMSL deserializer. The
GMSL deserializer locks to the serial data and outputs
the video data and clock.
Case 2: Sleep Mode
After power-up or when PWDN transitions from low to
high, the MAX9249 starts up in sleep mode. To wake up
the MAX9249, use the FC to send a GMSL protocol UART
frame containing at least three rising edges (e.g., 0x66),
at a bit rate no greater than 1Mbps. The low-power wake-
up receiver of the MAX9249 detects the wake-up frame
over the reverse control channel and powers up. Reset
the sleep bit (SLEEP = 0) of the MAX9249 using a regular
control channel write packet to power up the device fully.
Send the sleep bit write packet at least 500Fs after the
wake-up frame. The MAX9249 goes back to sleep mode
if its sleep bit is not cleared within 5ms (min) after detect-
ing a wake-up frame.
Applications Information
Self-PRBS Test
The MAX9249/GMSL deserializer link includes a PRBS
pattern generator and bit-error verification function. Set
PRBSEN =1 (0x04 D5) first in the MAX9249 and then the
GMSL deserializer to start the PRBS test. Set PRBSEN
=0 (0x04 D5) first in the GMSL deserializer and then the
MAX9249 to exit the PRBS self-test. The GMSL deserial-
izer uses an 8-bit register (0x0E) to count the number of
detected errors. The control link also controls the start
and stop of the error counting. During PRBS mode, the
device does not count decoding errors and the GMSL
deserializer ERR output reflects PRBS errors only. Refer
to the respective GMSL deserializer data sheet for more
details.
LOW
HIGH
1
0
SEREN
SLEEP
1
POWER-UP VALUE
SEREN = 0
FOR > 8ms
VIDEO LINK
OPERATING
VIDEO LINK
PRBS TEST
WAKE-UP
SLEEP = 1
WAKE-UP SIGNAL
REVERSE LINK
CONFIG
LINK STARTED
CLINKEN = 0 OR
SEREN = 1
CLINKEN = 1
UNLOCKED
LOCKED
CONFIG LINK
SLEEP = 0,
SLEEP
POWER-ON
IDLE
POWER-OFF
ALL STATES
PWDN = LOW OR
SLEEP = 1
POWER-DOWN
OR
POWER-OFF
AUTOS = LOW
PWDN = HIGH,
POWER-ON
VIDEO
LINK LOCKING
AUTOS PIN
SETTING
CONFIG LINK
OPERATING
PROGRAM
REGISTERS
CLINKEN = 0 OR
SEREN = 1
VIDEO LINK
LOCKED
VIDEO LINK
UNLOCKED
PRBSEN = 0
PRBSEN = 1
SEREN = 1,
RXCLKIN_ RUNNING
SEREN = 0 OR
NO RXCLKIN_
SEREN = 0 OR
NO RXCLKIN_
PWDN = HIGH,
POWER-ON,
AUTOS = HIGH
SLEEP = 0,
SLEEP = 1
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9257AGTL/V+ | IC SERDE PROG UART/I2C 40TQFN |
| MAX9257GTL+T | IC SER/DESER PROG 40-TQFN |
| MAX9260GCB/V+ | IC DESERIALIZER GMSL 64TQFP |
| MAX9271GTJ/V+ | IC SERIALIZER 16BIT GMSL 32TQFN |
| MAX9272GTM/V+ | IC DSERIALIZER 28BIT GMSL 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX924C/D | 功能描述:校验器 IC RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX924CPE | 功能描述:校验器 IC RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX924CPE+ | 功能描述:校验器 IC Quad Comparator w/1% Precision Ref RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX924CSE | 功能描述:校验器 IC Quad Comparator w/1% Precision Ref RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| MAX924CSE+ | 功能描述:校验器 IC Quad Comparator w/1% Precision Ref RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。