- 您现在的位置：买卖IC网 > PDF目录132964 > MB90561PFM 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | MB90561PFM |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件页数： | 8/91页 |
| 文件大小： | 931K |
| 代理商： | MB90561PFM |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页
MB90560/565 Series
16
Example of using an external clock
(7) Power supply pins
The multiple VCC and VSS pins are connected together in the internal device design so as to prevent misoperation
such as latch-up. However, always connect all VCC and VSS pins to the same potential externally to minimize
spurious radiation, prevent misoperation of strobe signals due to increases in the ground level, and maintain the
overall output current rating.
Also, ensure that the impedance of the VCC and VSS connections to the power supply is as low as possible.
To minimize these problems, connect a bypass capacitor of approximately 0.1
F between VCC and VSS. Connect
the capacitor close to the VCC and VSS pins.
(8) Sequence for connecting and disconnecting power supply
Do not apply voltage to the A/D converter power supply pins (AVCC, AVR, AVSS) or analog inputs (AN0 to AN7)
until the digital power supply (VCC) is turned on. When turning the device off, turn off the digital power supply
after disconnecting the A/D converter power supply and analog inputs. When turning the power on or off, ensure
that AVR does not exceed AVCC.
When using the I/O ports that share pins with the analog inputs, ensure that the input voltage does not exceed
AVCC (turning the analog and digital power supplies on and off simultaneously is OK) .
(9) Conditions when output from ports 0 and 1 is undefined
After turning on the power supply, the outputs from ports 0 and 1 are undefined during the oscillation stabilization
delay time controlled by the regulator circuit (during the power-on reset) if the RST pin level is “H”. When the
RST pin level is “L”, ports 0 and 1 go to high impedance.
Figures 1 and 2 show the timing (for the MB90F562/B and MB90V560) .
Note that this undefined output period does not occur on products without an internal regulator circuit as these
products do not have an oscillation stabilization delay time.
(MB90561/A, MB90562/A, MB90F568, and MB90567/8)
X0
X1
OPEN
MB90560/565 series
相关PDF资料 |
PDF描述 |
|---|---|
| MB90561P | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP64 |
| MB90F543PFV | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| MPC7410TRX500LE | 32-BIT, 500 MHz, RISC PROCESSOR, CBGA360 |
| MC68HC908QY4CP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP16 |
| MC68HC908QY4MDT | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB90562 | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562A | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562AP | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562APF | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
| MB90562APFM | 制造商:FUJITSU 制造商全称:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。