- 您现在的位置：买卖IC网 > PDF目录359132 > MC33389 (飞思卡尔半导体(中国)有限公司) System Basis Chip with Low Speed Fault Tolerant CAN(带低速容错CAN接口的系统基片) PDF资料下载
参数资料
| 型号： | MC33389 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | System Basis Chip with Low Speed Fault Tolerant CAN(带低速容错CAN接口的系统基片) |
| 中文描述： | 系统基础芯片与低速容错CAN（带低速容错的CAN接口的系统基片） |
| 文件页数： | 14/35页 |
| 文件大小： | 591K |
| 代理商： | MC33389 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
MC33389
14
MC33389
SBC MODES
Table 8. NormalRequest: V1 active, V2&V3 passive
SBC Normal Mode
In this mode, V1 and V2 are active, V3 can be set active or
passive via the SPI. Therefore, the whole ECU can be
operated. Normal mode is entered by a SWCR register
configuration in NormalRequest mode.
Table 9. SBC Normal Mode: V1 And V2 Are Active. V3 Is
Active Or Passive
SBC Standby Mode
In this mode V1 is active, V2 is passive. V3 can be either
permanently active or permanently passive. This is a low
power mode with V1 active in order to have a fast reaction
time in case of any wake-up.
For standby mode, the SBC monitors the SW. It means the
microcontroller runs and is monitored and must serve a
watchdog trigger.
Table 10. Standby: V1 Active V2 Passive, V3 Active Or
Passive, Watchdog Is Active
Entering NormalRequest
Leaving NormalRequest
SBC reset just released
When firstly receiving the
SW timing word, SBC
goes to Normal
If time-out without receiving
SPI commands (75ms),
SBC goes to sleep
Entering Normal Mode
Leaving Normal Mode
By SPI command
By SPI command, going to
any other mode
After SWCR register
configuration in
NormalRequest mode
Watchdog time out, going
to NormalRequest after
activating Reset
V1 undervoltage detection,
going to NormalRequest
mode after activating Reset
Entering Standby
Leaving Standby
If SW time-out going to
NormalRequest after
microcontroller Reset
By SPI command
By SPI command going to
any other mode
V1 undervoltage detection,
going to NormalRequest
mode after activating Reset
External activation of the
RSTB pin
SBC Sleep Mode
This is a low power consumption mode. V1 and V2 are
disabled. V3 can be permanently disabled or cyclically active.
Table 11. SBC Sleep Mode: V1 And V2 Are Passive, V3
Passive Or Cyclic.
Emergency Mode
In case the microcontroller detects the ECU or the system
is not under control any more, it may decide to switch the SBC
to the Emergency mode. V1, V2, V3 will be passive and wake-
up are not detected. The only way to leave this mode is to
disconnect the ECU from the Battery voltage (BatFail
detection).
Table 12. SBC Emergency Mode: V1 And V2 V3 Are
Passive
Figure 13. Typical Behaviour At Power On
Note: In Normalrequest, if an SPI command is received
before the SW timing configuration (SWCR register), it will not
Entering Sleep Mode
Leaving Sleep Mode
If SW timing not configured
75ms after entering
NormalRequest mode
CAN wake-up, going to
NormalRequest
By SPI command
If a wake-up is detected with
cyclic sense
For MC33389ADW only: If
V1 is below V1 reset for
more than 100ms
If a wake-up is detected with
wake-up not connected to V3
(permanent sense)
Forced wake-up (See Forced
Wake up Section)
SPI wake-up (See Wake up
by SPI Section)
Entering Emergency Mode
Leaving Emergency Mode
By SPI command
SBC BatFail detection (Dis-
connection of the Battery
voltage)
ECU
connected
to battery
Reset
V1 low
NormalRequest
Sleep
Normal
V1 on
SPI SW
timing configuration
at t<75ms
No SPI SW
timing configuration
at t=75ms
(reset
released)
Emergency
SPI go to Emergency
at t<75ms
Vbat > 4V and V1 low for t>100ms for MC33389ADW only (A version)
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33390 | J-1850 SERIAL TRANSCEIVER(串行J-1850总线收发器) |
| MC33394 | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(带有多个线性稳压器和高速CAN收发器的开关方式电源) |
| MC33395 | Three-Phase Gate Driver IC(3相栅极驱动器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(带SPI和并口输入控制的2或6低端开关) |
| MC33399 | “Local Interconnect Network” Physical Interface(“本地互联网”（LIN）物理接口) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33389CDH | 功能描述:IC SYSTEM BASIS W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDHR2 | 功能描述:IC SYSTEM BASE W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDW | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389CDWR2 | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389DDW | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。