- 您现在的位置：买卖IC网 > PDF目录359132 > MC33389 (飞思卡尔半导体(中国)有限公司) System Basis Chip with Low Speed Fault Tolerant CAN(带低速容错CAN接口的系统基片) PDF资料下载
参数资料
| 型号： | MC33389 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | System Basis Chip with Low Speed Fault Tolerant CAN(带低速容错CAN接口的系统基片) |
| 中文描述： | 系统基础芯片与低速容错CAN（带低速容错的CAN接口的系统基片） |
| 文件页数： | 16/35页 |
| 文件大小： | 591K |
| 代理商： | MC33389 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
MC33389
16
MC33389
WAKE-UP CAPABILITIES
Several wake up capabilities are available.
Forced Wake-up
The forced wake-up is enabled and disabled by SPI in
V3R register. It is used in sleep mode to automatically wake-
up the system by supplying V1 with proper reset. This
correspond to jump into NormalRequest mode. If then, the
SBC is not properly configured within 75ms, it switches back
to sleep mode till the next wake-up. If both Cyclic sense and
forced wake-up are enabled by the SPI in sleep mode, only
Cyclic sense will be active.
The period of forced wake-up are 32ms, 64ms, 128ms,
256ms, 512ms, 1024ms, 2048ms, 8192ms, chosen by SPI in
CYTCR register.
Wake-up Inputs (Local Wake-up) / Cyclic Sense
SBC provides 3 wake-up inputs to monitor external events
such as closing/opening of switches. The wake-up feature is
available in Normal, Standby and sleep modes. The switches
can be directly connected to V
bat
or to V3. The SBC must be
properly configured by setting bit WI2V3 in register V3R. In
this case, wake-ups are only detected when V3 is On. It can
take advantage of V3 cyclic sense feature. If both Cyclic
sense and forced wake-up are enabled by the SPI in sleep
mode, only Cyclic sense will be active.
Options For Wake Input
Different conditions for wake-up can be chosen for wake-
up input pins (via SPI in WUICR register).
No wake-up: No wake-up is detected, whatever occurs on
wake-up inputs.
High state: if the input pin voltage is above the detection
threshold during more than a 20
μ
s filter time, a wake-up is
detected. A flag is set in the WUISR register.
Low state: if the input pin voltage is below the detection
threshold during more than a 20
μ
s filter time, a wake-up is
detected. A flag is set in the WUISR register.
Change of state: each change of the wake-up input pin is
considered as a wake-up, if it lasts more than a 20
μ
s filter
time. The first reference state (no wake-up) is the wake-up
input state when the SBC is programmed to this option. A flag
is set in the WUISR register.
Multiple sampling events: when wake-up inputs are used
with V3 in cyclic sense in sleep mode.
For positive edge sensitivity, 2 samples Low followed by 2
samples High are necessary to validate the wake-up
condition.
For negative edge sensitivity, 2 samples High followed by
2 samples Low are necessary to validate the wake-up
condition.
For both edge sensitivity, 2 samples at a given state
followed by 2 samples in the opposite state are necessary to
validate the wake-up condition.
Wake-up Inputs With Cyclic Sense
Connecting the external switches to V3 allows power
saving since V3 can be programmed to be active, passive or
cyclic (cyclic sense). This gives a great flexibility to reduce
total power consumption while allowing full wake-up
capabilities. Cyclic sense is available only in sleep mode.
The period of the Cyclic sense can be chosen out of 8
different timings: 32ms, 64ms, 128ms, 256ms, 512ms,
1024ms, 2048ms, 8192ms programmable via SPI in CYTCR
register. Once activated, V3 remains ‘on’ during 400
μ
s. The
wake-up inputs states are sampled at 300
μ
s.
Figure 16. V3 Timing
Note: In sleep mode, the Cyclic Sense feature
‘EXCLUSIVE OR’ the forced Wake-up is chosen (not both).
Figure 17. Cyclic Sense Timing
Wake Up Inputs With Permanent Sense
Wake up detection can also be done on a permanent way
in Normal and Standby mode. If the contacts are connected to
V3, wake ups are only detected if V3 is on.
Wake ups are also detected on a permanent way in sleep
mode if the contacts are directly connected to V
bat
(if they are
connected to V3, only cyclic sense is available in sleep mode).
Local Wake-up Consequences
In normal or standby modes, the real time state of each
wake-up input pin is stored in the readable register WUIRTI.
Wake-ups are detected according to the option chosen. A flag
is set in the WUISR register. A maskable interrupt is sent via
INTB output.
In sleep mode, a local wake-up leads to a jump to
NormalRequest mode (via proper reset of the microcontroller). A
flag is set in the WUISR register.
Table 18. SBC Mode Versus Local Wake-up Behaviour
SBC Modes
Local Wake-up Behaviour
NormalRequest
No detection
300us
400us
V3passive
active
cyclic sense programmable period
wake-up inputs sample point
1
1
1
0
0
0
0
1
1
actual state (read)
memory state
INTB (wake-up active=0)
0
80ms
(t1)
160ms
V3
wake-up
switch status
V(L1)
Read L1
INTB
(t0)
OPEN
CLOSED
read
μ
s
setup
μ
s
sample point (80%)
zoomed
Cyclic sense connected to wake-up inputs. Example with wake-up input L1
sensitivity to Low state and timing=80ms
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33390 | J-1850 SERIAL TRANSCEIVER(串行J-1850总线收发器) |
| MC33394 | Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(带有多个线性稳压器和高速CAN收发器的开关方式电源) |
| MC33395 | Three-Phase Gate Driver IC(3相栅极驱动器) |
| MC33397 | Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(带SPI和并口输入控制的2或6低端开关) |
| MC33399 | “Local Interconnect Network” Physical Interface(“本地互联网”（LIN）物理接口) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33389CDH | 功能描述:IC SYSTEM BASIS W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDHR2 | 功能描述:IC SYSTEM BASE W/CAN 20-HSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33389CDW | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389CDWR2 | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389DDW | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。