- 您现在的位置：买卖IC网 > PDF目录11546 > MC33389CDW (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MC33389CDW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 11/49页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 标准包装： | 26 |
| 控制器类型： | 系统基础芯片 |
| 接口： | CAN |
| 电源电压： | 5.5 V ~ 18 V |
| 电流 - 电源： | 45mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33389
FUNCTIONAL DEVICE OPERATION
Supply and VBAT Block
VBAT Monitoring—VBAT is the main power supply coming
from the battery voltage after an external protection diode
(for reverse battery). VBAT is monitored for under voltage
and over voltage.
VBAT Under Voltage—VBAT is monitored for under voltage
if it is below 4.0 V the BatFail flag is set in the VSSR
register and a maskable interrupt is sent to the
microcontroller.
VBAT Over Voltage— When VBAT is > 20 V, the BatHigh
flag is set in the VSSR register. A maskable interrupt is
sent to the microcontroller. No specific action is taken to
reduce current consumption (to limit power dissipation).
This is to allow the entire flexibility to the microcontroller for
a decision.
CAN Transceiver
The device incorporates a low speed 125 kBaud CAN
physical interface. Its electrical parameters for the CANL,
CANH, RTL,RTH, RX, and TX pins are identical to the 33388,
stand alone CAN physical interface.
The mode control for the CAN transceiver (Normal, VBAT
Stand-by, Sleep, etc.) are selectable through the 33389 SPI
interface.
Baud Rate up to 125 kBit/s
Supports unshielded bus wires
Short-circuit proof to battery and ground in 12 V powered
systems
Supports single-wire transmission modes with ground
offset voltages up to 1.5 V
Automatic switching to single wire mode in case of bus
failures
Automatic reset to differential mode if bus failure is
removed
Low Electromagnetic Interference (EMI) due to built-in
slope control and signal symmetry
Fully integrated receiver filters
Thermally protected
Bus lines protected against automotive transients
Low current Bus Stand-by mode with wake-up capability
via the bus
An unpowered node does not disturb the bus lines
Figure 5. CAN Simplified Block Diagram
CONSEQUENCE OF FAILURE DETECTIONS
S1 is the switch from RTH to Ground
S2 is the switch from RTL to V2 and
S3 is the switch from RTL to VBAT
Each failure type provides data concerning which switch is
open and which driver is disabled.
Failure 1: Nothing done
Failure 2: Nothing done
Failure3: S1 open. Driver CANH is disabled
Failure4: S2 and S3 open. Driver CANL is disabled
Failure5: Nothing done
Failure6: S2 and S3 open. Driver CANL disabled
Failure7: S2 and S3 open. Driver CANL disabled
Failure8: S1 Open. CANH driver disable
CAN Transceiver Description
The CAN transceiver is an interface between CAN
protocol controller and the physical bus. It is intended for low
—
In Sleep Mode, During
Disable Time of Cyclic
Sense if Configured
—
Over Temp Threshold Reached
—
V1 Disabled (for any reason)
—
V2 Over Temperature Shutdown
Table 8. V3 Control
Termination
Protection
RX
TX
CAN_H
CAN_L
RTH
RTL
VDD2
SPI
Transmitter
Receiver
- Fail Detect
- Receive Mode
VDD2 VBAT
CAN Transceiver Register
Drivers
CAN transceiver simplified block diagram
12.5k
S3
S2
S1
VDD BAT
RTL
CANH
CANL
RTH
相关PDF资料 |
PDF描述 |
|---|---|
| MC33388DR2 | IC TOLERANT CAN INT FAULT 14SOIC |
| PX0414 | CONN SMB JACK PNL MNT RG174 |
| PIC16LF1937-E/PT | IC PIC MCU FLASH 512KX14 44-TQFP |
| PIC16F1934-E/ML | IC PIC MCU FLASH 256KX7 44-QFN |
| V48C12M75B | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33389CDWR2 | 功能描述:网络控制器与处理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389DDW | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33389DDWR2 | 功能描述:网络控制器与处理器 IC SBC SOW28 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33390D | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33390DR2 | 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。