参数资料
型号: MC33394
厂商: 飞思卡尔半导体(中国)有限公司
元件分类: CAN
英文描述: Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(带有多个线性稳压器和高速CAN收发器的开关方式电源)
中文描述: 开关电源的多线性稳压器和高速CAN收发器(带有多个线性稳压器和高速的CAN收发器的开关方式电源)
文件页数: 12/44页
文件大小: 641K
代理商: MC33394
12
Go to: www.freescale.com
3. ELECTRICAL CHARACTERISTICS
(–40
°
C
TA
+125
°
C; +4.0 V
VBAT
+26.5 V using the 33394 typical application
circuit – see Figure 1, unless otherwise noted.)
Characteristic
Symbol
Min.
Typ.
Max.
Unit
DC CHARACTERISTICS:
SUPERVISORY OUTPUTS
Reset Voltage Thresholds
/HRESET to follow /PRERESET by 0.7
μ
s
VDDH Reset Upper Threshold Voltage
(Note 1)
5.2
V
VDDH Reset Lower Threshold Voltage
(Note 1)
4.8
V
VDD3_3 Reset Upper Threshold Voltage
(Note 1)
3.43
V
VDD3_3 Reset Lower Threshold Voltage
(Note 1)
3.17
V
VDDL Reset Upper Threshold Voltage
(Notes 1, 4)
1.35
V
VDDL Reset Lower Threshold Voltage
(Notes 1, 4)
1.2
V
/PORESET Voltage Threshold
VKAM Reset Upper Threshold Voltage
(Notes 2, 5)
1.35
V
VKAM Reset Lower Threshold Voltage
(Notes 2, 5)
1.2
V
/PRERESET, /HRESET, /PORESET Open Drain Maximum Voltage
(Note 3)
7.0
V
/PRERESET, /HRESET, /PORESET Open Drain Pull–Down Current,
Vreset< 0.4 V
/PRERESET, /HRESET, /PORESET Low–Level Output Voltage,
IOL = 1.0 mA
1.0
mA
0.5
V
/PRERESET /HRESET /PORESET Leakage Current
15
μ
A
WAKEUP High–Level Output Voltage, IOH = –800
μ
A
VDDH–0.8
V
WAKEUP Low–Level Output Voltage, IOL = 1.6 mA
0.4
V
HRT Voltage Threshold
2.49
2.53
2.57
V
HRT Sink Current
1.0
mA
HRT Leakage Current
5.0
μ
A
HRT Saturation Voltage, HRT Current = 1 mA
0.4
V
AC CHARACTERISTICS:
SUPERVISORY OUTPUTS
/PORESET Delay
Delay time from VKAM in regulation and stable to the release of
/PORESET
7.0
10
15
ms
Reset Delay Time
Time from fault on VDDH, VDD3_3, VDDL or VKAM to Reset
(/PORESET, /PRERESET)
10
20
50
μ
s
/HRESET Delay Time
Time From /PRERESET low to /HRESET low
0.5
0.7
1.0
μ
s
VDDH, VDDL, VREF Power Up Sequence
Max Power Up Sequence Time Dependent on Output Load
Characteristics.
(Note 3)
800
μ
s
NOTE:
1. VDDH, VDD3_3, VDDL regulator outputs supervised by /PRERESET and /HRESET.
2. VKAM regulator output supervised by /PORESET.
3. Guaranteed by design but not production tested.
4. Measured at the VDDL_FB pin.
5. Measured at the VKAM_FB pin.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相关PDF资料
PDF描述
MC33395 Three-Phase Gate Driver IC(3相栅极驱动器)
MC33397 Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(带SPI和并口输入控制的2或6低端开关)
MC33399 “Local Interconnect Network” Physical Interface(“本地互联网”(LIN)物理接口)
MC33486 Dual High Side Switch for H-Bridge Automotive Applications(适合于H桥自动应用的双高端开关)
MC33661 LIN Enhanced Physical Interface(LIN网增强型物理接口)
相关代理商/技术参数
参数描述
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA,便携式音频/视频,智能电话 接口:I²C,2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘(4x4) 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2
MC33395DWB 功能描述:马达/运动/点火控制器和驱动器 TPD RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MC33395DWBR2 功能描述:马达/运动/点火控制器和驱动器 TPD RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MC33395EW 功能描述:马达/运动/点火控制器和驱动器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MC33395EWR2 功能描述:马达/运动/点火控制器和驱动器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube