参数资料
型号: MC33780EG
厂商: Freescale Semiconductor
文件页数: 7/37页
文件大小: 0K
描述: IC DBUS MASTER DUAL DIFF 16-SOIC
标准包装: 47
系列: *
类型: *
应用: *
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.295",7.50mm 宽)
供应商设备封装: 16-SOIC W
包装: 管件
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
33780
FUNCTIONAL DESCRIPTIONS
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
PROTOCOL ENGINE
This block converts the data to be transmitted from the
registers into the DBUS sequences, and converts DBUS
response sequences to data in the registers. It generates the
proper DBUS timing.
The DBUS transmit protocol uses a return to 1 type data
with a duty cycle determined by the logic state. The protocol
requires Cyclical Redundancy Check (CRC) generation and
validation.
Figure 10. Driver/Receiver Block Diagram
DBUS DRIVER /RECEIVER (PHYSICAL LAYER)
This block translates the transmit data to the voltage and
current needed to drive the DBUS. It also detects the
response current from the slave devices and translates that
current into digital levels. These circuits can drive their
outputs to the levels listed in Table 5.
The internal signal DSIF controls the Idle to Signalling
state change, and internal signal DSIS controls the signal
level, high or low. DSIR is the slave device response signal to
the logic. This is shown in Table 6.
The DBUS driver block diagram is shown in Figure 10. The
circuit uses independent drivers for the Idle and Signal states.
This allows each driver to be optimized for its function. The
Idle driver is active in Idle and during the transitions from Idle
to Signal high and Signal high to Idle. The Signal driver is only
active during actual signaling. Both drivers are disabled in
HiZ.
The Idle driver is required to supply a high current to
recharge the Slave device storage capacitors. It is also
required to drive the DBUS load capacitances and control the
slew rate over a wide supply voltage range. The DnH and
DnL Idle drivers are each optimized for their specific drive
requirements.
The Signal driver is optimized for driving the DBUS load,
and has the requirement of good slew rate control and
stability over a wide range of load conditions. The DnH and
DnL outputs use identical Signal driver circuits.
To ensure stability of the Signal driver, capacitors must be
connected between each output and ground. These are the
DBUS common mode capacitors. In addition, a bypass
capacitor is required at VSUP. These capacitors must be
located close to the IC pins and provide a low impedance
path to ground.
DnH
DnL
Differential
Control
DSIR
DSIS
DSIF
Common
Overvoltage TLIM
Signal
Generation
Mode
Correction
Signal
Idle
Comp.
Table 6. Internal Signal Truth Table
DSIF
DSIS
TLIM
DSIR
DnD
0
Return Data
Signal Low
0
1
0
Return Data
Signal High
1
0
High Impedance
1
0
Idle
X
1
0
High Impedance
相关PDF资料
PDF描述
MC33790DW IC DSI 2-CHAN INTERFACE 16-SOIC
MC33794EKR2 IC SENSOR ELECTRIC FIELD 54SOICW
MC33889BDW IC SYSTEM BASE W/CAN 28-SOIC
MC33889DPEG IC SYSTEM BASE W/CAN 28SOIC
MC33972TEWR2 IC SWITCH DETECT SPI 32-SOIC
相关代理商/技术参数
参数描述
MC33780EGR2 功能描述:IC DBUS MASTER DUAL DIFF 16-SOIC RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA(27x27) 包装:散装
MC33790DW 功能描述:IC DSI 2-CHAN INTERFACE 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG,串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP(0.173",4.40mm 宽) 供应商设备封装:20-TSSOP 包装:管件
MC33790HEG 功能描述:接口 - 专用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MC33790HEGR2 功能描述:接口 - 专用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MC33793D 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG,串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP(0.173",4.40mm 宽) 供应商设备封装:20-TSSOP 包装:管件