- 您现在的位置：买卖IC网 > PDF目录45205 > MC33780EGR2 (FREESCALE SEMICONDUCTOR INC) SPECIALTY MICROPROCESSOR CIRCUIT, PDSO16 PDF资料下载
参数资料
| 型号： | MC33780EGR2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PDSO16 |
| 封装： | 1.27 MM PITCH, ROHS COMPLIANT, SOIC-16 |
| 文件页数： | 5/37页 |
| 文件大小： | 851K |
| 代理商： | MC33780EGR2 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
33780
FUNCTIONAL DESCRIPTIONS
INTRODUCTION
FUNCTIONAL DESCRIPTIONS
INTRODUCTION
The 33780 is intended to be used as a master device in a
distributed system. It contains both protocol generators and
physical interfaces to allow an MCU to communicate with
devices on the bus using only a simple SPI interface. Two
differential busses are provided.
Using a loop-back wire allows operation of the bus in the
presence of an open circuit. This is immediate and no
interruption is caused by the open circuit. The differential
outputs have reduced electromagnetic radiation and
susceptibility.
The equivalent bus capacitance consists of capacitors
connected between the two bus wires and capacitors
between the bus wires and ground. Because the voltage
change on either of the bus wires to ground is only 1/2 the
amount of change between the two bus wires, the
capacitance to ground only conducts half as much current as
it would if connected directly across the bus. The equivalent
bus capacitance of a capacitor to ground from the bus wires
is one half of the actual amount of the capacitor. The amount
of capacitance from either bus wire to ground should be kept
the same in order to achieve the lowest radiated EMI energy.
The 4.7 nF capacitors required between the bus wires and
ground result in an equivalent of 2.35 nF of capacitance
across the bus as seen by either bus wire.
Table 5 shows the voltages used for operation. Low side
(LS) is the bus wire that is the most negative and high side
(HS) is the bus wire that is the most positive. Figure 5 shows
the bus waveforms in normal operation.
FUNCTIONAL PIN DESCRIPTIONS
RESET (RST)
When pulled low, this will reset all internal registers to a
known state as indicated in the section entitled Register and Bit
CHIP SELECT (CS)
This input is used to select the SPI port when pulled to
ground. When high, the SPI signals are ignored. The SPI
transaction is signaled as completed when this signal returns
high.
INTERRUPT (INT)
This output will be asserted ow when an enabled interrupt
condition occurs. It contains an internal current pull-up
source so that it will remain high when not active. The output
is open-drain so that it can be ORed together with other open-
drain outputs so that this IC or any of the others can assert an
interrupt.
MASTER OUT/SLAVE IN (MOSI)
This is the SPI data input to the device. This data is
sampled on the positive (rising) edge of SCLK.
SERIAL CLOCK (SCLK)
This is the clock signal from the SPI master device. It
controls the clocking of data to the device and data read from
the device.
MASTER IN/SLAVE OUT (MISO)
This is the SPI data from the device to the SPI master (the
MCU). Data changes on the negative (falling) transition of the
SCLK.
CLOCK (CLK)
This is the main clock source for the internal logic. It must
be 4.0 MHz.
GROUND (GND)
Ground source for both logic and DBUS return.
POWER SOURCE (VCC)
Logic power source. Nominal value is +5.0 V. This should
be bypassed with a small capacitor to ground (0.01-0.1 F)
LOW-SIDE BUS (DnL)
There are two independent LOW-SIDE outputs, D0L and
D1L They comprise the low-side differential output signal of
Table 5. High-Side and Low-Side Typical Voltages (Voltage Relative to Ground)
Low Side
High Side
IDLE
HIGH
LOW
IDLE
HIGH
LOW
0
Vmid-2.25 (18)
Vmid-0.75 (18)
VSUP
Vmid+2.25 (18)
Vmid+0.75 (18)
Notes
18
Vmid = VSUP/2.
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33780EG | SPECIALTY MICROPROCESSOR CIRCUIT, PDSO16 |
| MC3S12Q64CFA8 | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48 |
| MC3S12Q128VPB16 | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP52 |
| MC9S12Q32MPB16 | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP52 |
| MC3S12Q128CFA16 | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33790DW | 功能描述:IC DSI 2-CHAN INTERFACE 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| MC33790HEG | 功能描述:接口 - 专用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33790HEGR2 | 功能描述:接口 - 专用 DISTRIB SYS INTRFC RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33793D | 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| MC33793DR2 | 功能描述:IC DSI SLAVE FOR R-SENSE 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。