- 您现在的位置：买卖IC网 > PDF目录11567 > MC33889DPEGR2 (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28SOIC PDF资料下载
参数资料
| 型号： | MC33889DPEGR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 29/59页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28SOIC |
| 标准包装： | 1,000 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Analog Integrated Circuit Device Data
Freescale Semiconductor
35
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
MC33889B:
When detection is complete, the counter is no longer incremented. It can only be decremented by sampling of the dominant
level on the S-H (S-L) (recovery pulse). When it reaches zero, the failure has recovered.
In application, with CAN communication, a recovery condition is detected after 4 acknowledge bits are sent by the MC33889B.
MC333889D:
When detection is complete, the counter is decremented by sampling the dominant pulse (recovery pulse) on S-H (S-L), and
incremented (up to 4) by sampling the recessive pulse (detection pulses) on S-H (S-L). It is necessary to get 4 consecutive
dominant samples (recovery pulse) to get to zero. When reaching zero, the failure is recovered.
In application with real CAN communication, a recovery condition will not be detected by a single acknowledge bit send by
MC33889D, but requires a complete CAN message (at least 4 dominant bits) send in dual wire mode, without reception of any
bit in single wire mode.
Tx permanent dominant detection:
In addition to the previous list, the 33889 detects a permanent low state at the TX input which results in a permanent dominant
bus state. If TX is low for more than 0.75-4.0 ms, the bus output driver is disabled. This avoids blocking communication between
other nodes of the network. TXD is reported via the SPI (RCR register bit D1: TXFAILURE). Tx permanent dominant recovery is
done with TX recessive for more than typ 32
s.
Rx pin behavior while CAN interface is in TermVBAT.
The MC33889D is able to signal bus activity on Rx while the CAN interface is in TermVBAT and the SBC in normal or standby
mode. When the bus is driven into a dominant state by another sending node, each dominant state is reported at Rx by a low
level, after a delay of tWAKE.
The bus state report is done through the CAN interface wake-up comparator on CANL and CANH, and thus operates also in
case of bus failure. This is illustrated in Figure 16.
相关PDF资料 |
PDF描述 |
|---|---|
| V375A5C400BG3 | CONVERTER MOD DC/DC 5V 400W |
| CP82C59AZ | IC INTERFACE 5V 8MHZ 28-DIP |
| V375A5C400BG2 | CONVERTER MOD DC/DC 5V 400W |
| V375A5C400BF3 | CONVERTER MOD DC/DC 5V 400W |
| V375A5C400BF2 | CONVERTER MOD DC/DC 5V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33889DW | 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33889DWR2 | 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| MC33895FC | 功能描述:IC H-BRIDGE QUAD W/LIN 32-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33897AEF | 功能描述:网络控制器与处理器 IC SWCAN PB FREE P 2.4 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33897AEFR2 | 功能描述:网络控制器与处理器 IC SWCAN PB FREE P 2.4 RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。