- 您现在的位置：买卖IC网 > PDF目录11657 > MC56F8006VWL (Freescale Semiconductor)DSC 16K FLASH 32MHZ 28-SOIC PDF资料下载
参数资料
| 型号： | MC56F8006VWL |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 35/106页 |
| 文件大小： | 0K |
| 描述： | DSC 16K FLASH 32MHZ 28-SOIC |
| 标准包装： | 26 |
| 系列： | 56F8xxx |
| 核心处理器： | 56800E |
| 芯体尺寸： | 16-位 |
| 速度： | 32MHz |
| 连通性： | I²C，LIN，SCI，SPI |
| 外围设备： | LVD，POR，PWM，WDT |
| 输入/输出数： | 23 |
| 程序存储器容量： | 16KB（8K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 3.6 V |
| 数据转换器： | A/D 15x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 734 (CN2011-ZH PDF) |
| 配用： | MC56F8006DEMO-ND - DEMO BOARD FOR MC56F8006 APMOTOR56F8000E-ND - KIT DEMO MOTOR CTRL SYSTEM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
MC56F8006/MC56F8002 Digital Signal Controller, Rev. 4
General System Control Information
Freescale Semiconductor
34
6
General System Control Information
6.1
Overview
This section discusses power pins, reset sources, interrupt sources, clock sources, the system integration module (SIM), ADC
synchronization, and JTAG/EOnCE interfaces.
6.2
Power Pins
VDD, VSS and VDDA, VSSA are the primary power supply pins for the devices. This voltage source supplies power to all on-chip
peripherals, I/O buffer circuitry and to internal voltage regulators. Device has multiple internal voltages provide regulated
lower-voltage source for the peripherals, core, memory, and on-chip relaxation oscillators.
Typically, there are at least two separate capacitors across the power pins to bypass the glitches and provide bulk charge storage.
In this case, there should be a bulk electrolytic or tantalum capacitor, such as a 10
F tantalum capacitor, to provide bulk charge
storage for the overall system and a 0.1
F ceramic bypass capacitor located as near to the device power pins as practical to
suppress high-frequency noise. Each pin must have a bypass capacitor for best noise suppression.
VDDA and VSSAare the analog power supply pins for the device. This voltage source supplies power to the ADC, PGA, and
CMP modules. A 0.1
F ceramic bypass capacitor should be located as near to the device VDDA and VSSA pins as practical to
suppress high-frequency noise. VDDA and VSSA are also the voltage reference high and voltage reference low inputs,
respectively, for the ADC module.
6.3
Reset
Resetting the device provides a way to start processing from a known set of initial conditions. During reset, most control and
status registers are forced to initial values and the program counter is loaded from the reset vector. On-chip peripheral modules
are disabled and I/O pins are initially configured as the reset status shown in Table 5. The 56F8006/56F8002 has the following
sources for reset:
Power-on reset (POR)
Partial power down reset (PPD)
Low-voltage detect (LVD)
External pin reset (EXTR)
Computer operating properly loss of reference reset (COP_LOR)
Computer operating properly time-out reset (COP_CPU)
Software Reset (SWR)
Each of these sources has an associated bit in the reset status register (RSTAT) in the system integration module (SIM).
The external pin reset function is shared with an GPIO port A7 on the RESET/GPIOA7 pin. The reset function is enabled
following any reset of the device. Bit 7 of GPIOA_PER register must be cleared to use this pin as an GPIO port pin. When
enabled as the RESET pin, an internal pullup device is automatically enabled.
6.4
On-chip Clock Synthesis
The on-chip clock synthesis (OCCS) module allows designers using an internal relaxation oscillator, an external crystal, or an
external clock to run 56F8000 family devices at user-selectable frequencies up to 32 MHz.
The features of OCCS module include:
Ability to power down the internal relaxation oscillator or crystal oscillator
Ability to put the internal relaxation oscillator into standby mode
Ability to power down the PLL
相关PDF资料 |
PDF描述 |
|---|---|
| V110C15M100BF | CONVERTER MOD DC/DC 15V 100W |
| V110C15M100B3 | CONVERTER MOD DC/DC 15V 100W |
| V110B5M100BL3 | CONVERTER MOD DC/DC 5V 100W |
| V110B5M100BG3 | CONVERTER MOD DC/DC 5V 100W |
| V110B5M100B2 | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC56F8006VWL | 制造商:Freescale Semiconductor 功能描述:IC DSC 16BIT 16KB 32MHZ 3.6V SOIC-28 |
| MC56F8006VWLR | 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8011 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers |
| MC56F8011VFAE | 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC ANGUILLA RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8013 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers |
发布紧急采购，3分钟左右您将得到回复。