- 您现在的位置：买卖IC网 > PDF目录80445 > MC68HC05C8AMFB (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | MC68HC05C8AMFB |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | QFP-44 |
| 文件页数： | 78/116页 |
| 文件大小： | 781K |
| 代理商： | MC68HC05C8AMFB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页当前第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页
Serial Peripheral Interface (SPI)
MC68HC05C8A MC68HCL05C8A MC68HSC05C8A Data Sheet, Rev. 5.1
64
Freescale Semiconductor
10.5.2 Serial Peripheral Status Register
SPIF — SPI Transfer Complete Flag
The serial peripheral data transfer flag bit is set upon completion of data transfer between the
processor and external device. If SPIF goes high and if SPIE is set, a serial peripheral interrupt is
generated. Clearing the SPIF bit is accomplished by reading the SPSR (with SPIF set) followed by an
access of the SPDR. Unless SPSR is read (with SPIF set) first, attempts to write to SPDR are inhibited.
WCOL — Write Collision Bit
The write collision bit is set when an attempt is made to write to the serial peripheral data register while
data transfer is taking place. If CPHA is 0, a transfer is said to begin when SS goes low and the transfer
ends when SS goes high after eight clock cycles on SCK. When CPHA is 1, a transfer is said to begin
the first time SCK becomes active while SS is low. The transfer ends when the SPIF flag gets set.
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by an access
to SPDR.
Bit 5 — Not implemented
This bit always reads as 0.
MODF — Mode Fault Flag
The mode fault flag indicates that there may have been a multi-master conflict for system control and
allows a proper exit from system operation to a reset or default system state. The MODF bit is normally
clear and is set only when the master device has its SS pin pulled low. Setting the MODF bit affects
the internal serial peripheral interface system in these ways:
An SPI interrupt is generated if SPIE = 1.
The SPE bit is cleared. This disables the SPI.
The MSTR bit is cleared, thus forcing the device into the slave mode.
Clearing the MODF bit is accomplished by reading the SPSR (with MODF set), followed by a write to
the SPCR. Control bits SPE and MSTR may be restored by user software to their original state after
the MODF bit has been cleared.
Bits 3–0 — Not Implemented
These bits always reads as 0.
Address: $000B
Bit 7
654321
Bit 0
Read:
SPIF
WCOL
0
MODF
0000
Write:
Reset
000000
U
= Unimplemented
U = Unaffected
Figure 10-5. SPI Status Register (SPSR)
相关PDF资料 |
PDF描述 |
|---|---|
| MPC8250ACVRMIBX | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA516 |
| MPC860TZQ50D4R2 | 32-BIT, 50 MHz, RISC PROCESSOR, PBGA357 |
| MC908GZ48VFU | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 |
| MC9S12GC32PCFA25 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP48 |
| MC9S12KG128CPU | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05C9 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:TECHNICAL DATA |
| MC68HC05C9A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AB | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AFB | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05C9AFN | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。