- 您现在的位置：买卖IC网 > PDF目录11943 > MC68HC11D0CFBE3 (Freescale Semiconductor)IC MCU 8BIT 3MHZ 44-QFP PDF资料下载
参数资料
| 型号： | MC68HC11D0CFBE3 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 107/124页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8BIT 3MHZ 44-QFP |
| 标准包装： | 480 |
| 系列： | HC11 |
| 核心处理器： | HC11 |
| 芯体尺寸： | 8-位 |
| 速度： | 3MHz |
| 连通性： | SCI，SPI |
| 外围设备： | POR，WDT |
| 输入/输出数： | 26 |
| 程序存储器类型： | ROMless |
| RAM 容量： | 192 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-QFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页当前第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
SERIAL PERIPHERAL INTERFACE
TECHNICAL DATA
8-5
indicates that an attempt was made to write data to the SPDR while a transfer was in
progress.
When the SPI system is configured as a master and the SS input line goes to active
low, a mode fault error has occurred — usually because two devices have attempted
to act as master at the same time. In cases where more than one device is concurrent-
ly configured as a master, there is a chance of contention between two pin drivers. For
push-pull CMOS drivers, this contention can cause permanent damage. The mode
fault attempts to protect the device by disabling the drivers. The MSTR control bit in
the SPCR and all four DDRD control bits associated with the SPI are cleared. An in-
terrupt is generated subject to masking by the SPIE control bit and the I bit in the CCR.
Other precautions may need to be taken to prevent driver damage. If two devices are
made masters at the same time, mode fault does not help protect either one unless
one of them selects the other as slave. The amount of damage possible depends on
the length of time both devices attempt to act as master.
A write collision error occurs if the SPDR is written while a transfer is in progress. Be-
cause the SPDR is not double buffered in the transmit direction, writes to SPDR cause
data to be written directly into the SPI shift register. Because this write corrupts any
transfer in progress, a write collision error is generated. The transfer continues undis-
turbed, and the write data that caused the error is not written to the shifter.
A write collision is normally a slave error because a slave has no control over when a
master initiates a transfer. A master knows when a transfer is in progress, so there is
no reason for a master to generate a write-collision error, although the SPI logic can
detect write collisions in both master and slave devices.
The SPI configuration determines the characteristics of a transfer in progress. For a
master, a transfer begins when data is written to SPDR and ends when SPIF is set.
For a slave with CPHA equal to zero, a transfer starts when SS goes low and ends
when SS returns high. In this case, SPIF is set at the middle of the eighth SCK cycle
when data is transferred from the shifter to the parallel data register, but the transfer
is still in progress until SS goes high. For a slave with CPHA equal to one, transfer be-
gins when the SCK line goes to its active level, which is the edge at the beginning of
the first SCK cycle. The transfer ends in a slave in which CPHA equals one when SPIF
is set. For a slave, after a byte transfer, SCK must be in inactive state for at least 2 E-
clock cycles before the next byte transfer begins.
8.5 SPI Registers
The three SPI registers, SPCR, SPSR, and SPDR, provide control, status, and data
storage functions. Refer to the following information for a description of how these reg-
isters are organized.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S08QG8CFFE | IC MCU 8K FLASH 10MHZ 16-QFN |
| MC9S08QG8CFKE | IC MCU 8K FLASH 24-QFN |
| MC9S08SE8CTG | IC MCU 8BIT 8K FLASH 16TSSOP |
| MC9S08QG4CFFE | IC MCU 4K FLASH 10MHZ 16-QFN |
| MC9S08QG8CDTER | IC MCU 8BIT 8K FLASH 16-TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC11D0CFBE3R | 功能描述:8位微控制器 -MCU 8B MCU 192RAM 3 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MC68HC11D0CFN2 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC11D0CFN3 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| MC68HC11D0CFNE2 | 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MC68HC11D0CFNE2R | 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。