- 您现在的位置：买卖IC网 > PDF目录4934 > MCP1826ST-0802E/DB (Microchip Technology)IC REG LDO 0.8V 1A SOT223-3 PDF资料下载
参数资料
| 型号： | MCP1826ST-0802E/DB |
| 厂商： | Microchip Technology |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 0.8V 1A SOT223-3 |
| 产品培训模块： | High Current LDOs |
| 标准包装： | 4,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 0.8V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.25V @ 1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223-3 |
| 包装： | 带卷 (TR) |
| 其它名称： | MCP1826ST-0802E/DBTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MCP1826/MCP1826S
4.0
DEVICE OVERVIEW
EQUATION 4-2:
R 1 = R 2 ? -------------------------------- ?
V ADJ
The MCP1826/MCP1826S is a high output current,
Low Dropout (LDO) voltage regulator. The low dropout
voltage of 300 mV typical at 1000 mA of current makes
Where:
V OUT – V ADJ
? ?
it ideal for battery-powered applications. Unlike other
high output current LDOs, the MCP1826/MCP1826S
only draws a maximum of 220 μA of quiescent current.
The MCP1826 has a shutdown control input and a
V OUT
V ADJ
=
=
LDO Output Voltage
ADJ Pin Voltage
(typically 0.41V)
power good output.
4.1
LDO Output Voltage
4.2
Output Current and Current
Limiting
The 5-pin MCP1826 LDO is available with either a fixed
output voltage or an adjustable output voltage. The
output voltage range is 0.8V to 5.0V for both versions.
The 3-pin MCP1826S LDO is available as a fixed
voltage device.
4.1.1 ADJUST INPUT
The adjustable version of the MCP1826 uses the ADJ
pin (pin 5) to get the output voltage feedback for output
voltage regulation. This allows the user to set the
output voltage of the device with two external resistors.
The nominal voltage for ADJ is 0.41V.
MCP1826. Resistors R 1 and R 2 form the resistor
divider network necessary to set the output voltage.
With this configuration, the equation for setting V OUT is:
EQUATION 4-1:
The MCP1826/MCP1826S LDO is tested and ensured
to supply a minimum of 1000 mA of output current. The
MCP1826/MCP1826S has no minimum output load, so
the output load current can go to 0 mA and the LDO will
continue to regulate the output voltage to within
tolerance.
The MCP1826/MCP1826S also incorporates an output
current limit. If the output voltage falls below 0.7V due
to an overload condition (usually represents a shorted
load condition), the output current is limited to 2.2A
(typical). If the overload condition is a soft overload, the
MCP1826/MCP1826S will supply higher load currents
of up to 2.5A. The MCP1826/MCP1826S should not be
operated in this condition continuously as it may result
in failure of the device. However, this does allow for
device usage in applications that have higher pulsed
load currents having an average output current value of
1000 mA or less.
V OUT = V ADJ ? ------------------ ?
R 2
Where:
V OUT
V ADJ
=
=
R 1 + R 2
? ?
LDO Output Voltage
ADJ Pin Voltage
(typically 0.41V)
MCP1826-ADJ
V OUT
Output overload conditions may also result in an over-
temperature shutdown of the device. If the junction
temperature rises above 150°C, the LDO will shut
perature Protection” for more information on
overtemperature shutdown.
4.3
Output Capacitor
The MCP1826/MCP1826S requires a minimum output
capacitance of 1 μF for output voltage stability. Ceramic
capacitors are recommended because of their size,
O ff
On
SHDN
1 2 3 4 5
ADJ
R 1
C2
1 μF
cost and environmental robustness qualities.
Aluminum-electrolytic and tantalum capacitors can be
V IN
C 1
4.7 μF
GND
R 2
used on the LDO output as well. The Equivalent Series
Resistance (ESR) of the electrolytic output capacitor
must be no greater than 1 ohm. The output capacitor
should be located as close to the LDO output as is
practical. Ceramic materials X7R and X5R have low
FIGURE 4-1: Typical adjustable output
voltage application circuit.
The allowable resistance value range for resistor R 2 is
from 10 k Ω to 200 k Ω . Solving the equation for R 1
yields the following equation:
temperature coefficients and are well within the
acceptable ESR range required. A typical 1 μF X7R
0805 capacitor has an ESR of 50 milli-ohms.
Larger LDO output capacitors can be used with the
MCP1826/MCP1826S to improve dynamic
performance and power supply ripple rejection
performance. A maximum of 22 μF is recommended.
Aluminum-electrolytic capacitors
are not recom-
mended for low-temperature applications of ≤ 25°C.
DS22057A-page 16
? 2007 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| RSM18DTAH-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| UPJ1J221MHD | CAP ALUM 220UF 63V 20% RADIAL |
| TC1264-3.3VDB | IC REG LDO 3.3V .8A SOT223-3 |
| MCP1726T-5002E/MF | IC REG LDO 5V 1A 8DFN |
| MCP1726-1202E/MF | IC REG LDO 1.2V 1A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1826ST-1202E/DB | 功能描述:低压差稳压器 - LDO 1A CMOS LDO Vout 1.2V ETR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1826ST-1202E/EB | 功能描述:低压差稳压器 - LDO 1A CMOS LDO Vout 1.2V ETR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1826ST-1802E/DB | 功能描述:低压差稳压器 - LDO 1A CMOS LDO Vout 1.8V ETR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1826ST-1802E/EB | 功能描述:低压差稳压器 - LDO 1A CMOS LDO Vout 1.8V ETR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1826ST-2502E/DB | 功能描述:低压差稳压器 - LDO 1A CMOS LDO Vout 2.5V ETR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。