参数资料
型号: MCP2510-I/SO
厂商: Microchip Technology
文件页数: 48/80页
文件大小: 0K
描述: IC CAN CONTRLER IND TEMP 18SOIC
产品培训模块: CAN Bus Protection
标准包装: 42
控制器类型: CAN 接口
接口: SPI
电源电压: 3 V ~ 5.5 V
电流 - 电源: 10mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
供应商设备封装: 18-SOIC
包装: 管件
产品目录页面: 685 (CN2011-ZH PDF)
配用: DV251001-ND - KIT DEVELOPMENT CAN MCP2510
MCP2510
DS21291F-page 52
2007 Microchip Technology Inc.
counters are reset and deactivated in this state. The lis-
ten-only mode is activated by setting the mode request
bits in the CANCTRL register.
9.4
Loopback Mode
This mode will allow internal transmission of messages
from the transmit buffers to the receive buffers without
actually transmitting messages on the CAN bus. This
mode can be used in system development and testing.
In this mode the ACK bit is ignored and the device will
allow incoming messages from itself just as if they were
coming from another node. The loopback mode is a
silent mode, meaning no messages will be transmitted
while in this state, including error flags or acknowledge
signals. The TXCAN pin will be in a reccessive state
while the device is in this mode. The filters and masks
can be used to allow only particular messages to be
loaded into the receive registers. The masks can be set
to all zeros to provide a mode that accepts all mes-
sages. The loopback mode is activated by setting the
mode request bits in the CANCTRL register.
9.5
Normal Mode
This is the standard operating mode of the MCP2510.
In this mode the device actively monitors all bus mes-
sages and generates acknowledge bits, error frames,
etc. This is also the only mode in which the MCP2510
will transmit messages over the CAN bus.
REGISTER 9-1:
CANCTRL - CAN CONTROL REGISTER (ADDRESS: XFh)
R/W-1
R/W-0
U-0
R/W-1
REQOP2
REQOP1
REQOP0
ABAT
CLKEN
CLKPRE1 CLKPRE0
bit 7
bit 0
bit 7-5
REQOP<2:0>: Request Operation Mode
000
= Set Normal Operation Mode
001
= Set Sleep Mode
010
= Set Loopback Mode
011
= Set Listen Only Mode
100
= Set Configuration Mode
All other values for REQOP bits are invalid and should not be used
Note:
On power up, REQOP = b’111’
bit 4
ABAT: Abort All Pending Transmissions
1
= Request abort of all pending transmit buffers
0
= Terminate request to abort all transmissions
bit 3
Unimplemented: Read as '0'
bit 2
CLKEN: CLKOUT Pin Enable
1
= CLKOUT pin enabled
0
= CLKOUT pin disabled (Pin is in high impedance state)
bit 1-0
CLKPRE <1:0>: CLKOUT Pin Prescaler
00
=FCLKOUT = System Clock/1
01
=FCLKOUT = System Clock/2
10
=FCLKOUT = System Clock/4
11
=FCLKOUT = System Clock/8
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
’1’ = Bit is set
’0’ = Bit is cleared
x = Bit is unknown
相关PDF资料
PDF描述
V48C28M75BF CONVERTER MOD DC/DC 28V 75W
V48C28M75BL3 CONVERTER MOD DC/DC 28V 75W
D38999/20MJ7SN CONN RCPT 99POS WALL MNT W/SCKT
D38999/20JJ7SN CONN RCPT 99POS WALL MNT W/SCKT
V48C24M75BL CONVERTER MOD DC/DC 24V 75W
相关代理商/技术参数
参数描述
MCP2510-IST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface
MCP2510I-ST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPIa?¢ Interface
MCP2510T-/P 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI⑩ Interface
MCP2510T-/SO 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI⑩ Interface
MCP2510T-/ST 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI⑩ Interface