- 您现在的位置：买卖IC网 > PDF目录1229 > MCP2515DM-PTPLS (Microchip Technology)BOARD DAUGHTER PICTAIL MCP2515 PDF资料下载
参数资料
| 型号： | MCP2515DM-PTPLS |
| 厂商： | Microchip Technology |
| 文件页数： | 39/92页 |
| 文件大小： | 0K |
| 描述： | BOARD DAUGHTER PICTAIL MCP2515 |
| 标准包装： | 1 |
| 系列： | * |
| 主要目的： | 接口，CAN 控制器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP2515，MCP2551 |
| 主要属性： | 置于 PICtail Plus 子板内的 CAN 控制器和 CAN 收发器 |
| 已供物品： | 板，CD |
| 产品目录页面： | 685 (CN2011-ZH PDF) |
| 相关产品： | MCP2515T-I/ST-ND - IC CAN CONTROLLER W/SPI 20TSSOP MCP2515T-I/SO-ND - IC CAN CONTROLLER W/SPI 18SOIC MCP2515T-E/ST-ND - IC CAN CONTROLLER W/SPI 20TSSOP MCP2515T-E/SO-ND - IC CAN CONTROLLER W/SPI 18SOIC MCP2515-E/ST-ND - IC CAN CONTROLLER W/SPI 20TSSOP MCP2515-E/SO-ND - IC CAN CONTROLLER W/SPI 18SOIC MCP2515-E/P-ND - IC CAN CONTROLLER W/SPI 18DIP MCP2515-I/ST-ND - IC CAN CONTROLLER W/SPI 20TSSOP MCP2515-I/SO-ND - IC CAN CONTROLLER W/SPI 18SOIC MCP2515-I/P-ND - IC CAN CONTROLLER W/SPI 18DIP 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MCP2515
5.0
BIT TIMING
5.1
The CAN Bit TIme
NBR = fbit = -------
All nodes on a given CAN bus must have the same
nominal bit rate. The CAN protocol uses Non Return to
Zero (NRZ) coding, which does not encode a clock
within the data stream. Therefore, the receive clock
must be recovered by the receiving nodes and
synchronized to the transmitter ’s clock.
As oscillators and transmission times may vary from
node to node, the receiver must have some type of
Phase Lock Loop (PLL) synchronized to data
transmission edges to synchronize and maintain the
receiver clock. Since the data is NRZ-coded, it is
necessary to include bit-stuffing to ensure that an edge
occurs at least every six bit times to maintain the Digital
Phase Lock Loop (DPLL) synchronization.
The bit timing of the MCP2515 is implemented using a
DPLL that is configured to synchronize to the incoming
data, as well as provide the nominal timing for the
transmitted data. The DPLL breaks each bit time into
multiple segments made up of minimal periods of time,
called the Time Quanta (TQ).
Bus timing functions executed within the bit time frame
(such as synchronization to the local oscillator, network
transmission delay compensation and sample point
positioning) are defined by the programmable bit timing
logic of the DPLL.
All devices on the CAN bus must use the same bit rate.
However, all devices are not required to have the same
master oscillator clock frequency. For the different
clock frequencies of the individual devices, the bit rate
has to be adjusted by appropriately setting the Baud
Rate Prescaler and number of time quanta in each
segment.
The CAN bit time is made up of non-overlapping
segments. Each of these segments are made up of
integer units called Time Quanta (TQ), explained later
in this data sheet. The Nominal Bit Rate (NBR) is
defined in the CAN specification as the number of bits
per second transmitted by an ideal transmitter with no
resynchronization. It can be described with the
equation:
EQUATION 5-1:
1
t bit
Nominal Bit Time
The Nominal Bit Time (NBT) (t bit ) is made up of non-
overlapping segments ( Figure 5-1 ). Therefore, the
NBT is the summation of the following segments:
t bit = t SyncSeg + t PropSeg + t PS1 + t PS2
Associated with the NBT are the sample point,
Synchronization Jump Width (SJW) and Information
Processing Time (IPT), which are explained later.
SYNCHRONIZATION SEGMENT
The Synchronization Segment (SyncSeg) is the first
segment in the NBT and is used to synchronize the
nodes on the bus. Bit edges are expected to occur
within the SyncSeg. This segment is fixed at 1 TQ.
FIGURE 5-1:
CAN BIT TIME SEGMENTS
SyncSeg
PropSeg
PhaseSeg1 (PS1)
PhaseSeg2 (PS2)
Sample
Point
Nominal Bit Time (NBT), t bit
? 2003-2012 Microchip Technology Inc.
DS21801G-page 39
相关PDF资料 |
PDF描述 |
|---|---|
| MCP3905EV | BOARD DEMO FOR MCP3905 |
| MCP402XEV | BOARD EVAL FOR MCP402X |
| MCP42XXEV | BOARD EVALUATION MCP42XX |
| MCP43XXEV | BOARD EVALUATION MCP43XX |
| MCP46XXDM-PTPLS | BOARD PICTAIL DIGI POT MCP4XXX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2515-E | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2515-E/ML | 制造商:Microchip Technology Inc 功能描述: |
| MCP2515-E/P | 功能描述:网络控制器与处理器 IC W/ SPI Inter 125dC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2515-E/SO | 功能描述:网络控制器与处理器 IC W/ SPI Inter 125dC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2515-E/SORB4 | 制造商:Microchip Technology Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。