- 您现在的位置：买卖IC网 > PDF目录10735 > MCP3001-I/MS (Microchip Technology)IC ADC 10BIT 2.7V 1CH SPI 8MSOP PDF资料下载
参数资料
| 型号： | MCP3001-I/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 2.7V 1CH SPI 8MSOP |
| 标准包装： | 100 |
| 位数： | 10 |
| 采样率（每秒）： | 200k |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 产品目录页面： | 672 (CN2011-ZH PDF) |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
2007 Microchip Technology Inc.
DS21293C-page 13
MCP3001
3.0
PIN DESCRIPTIONS
3.1
IN+
Positive analog input. This input can vary from IN- to
V
REF + IN-.
3.2
IN-
Negative analog input. This input can vary ±100 mV
from V
SS.
3.3
CS/SHDN(Chip Select/Shutdown)
The CS/SHDN pin is used to initiate communication
with the device when pulled low and will end a conver-
sion and put the device in low power standby when
pulled high. The CS/SHDN pin must be pulled high
between conversions.
3.4
CLK (Serial Clock)
The SPI clock pin is used to initiate a conversion and to
clock out each bit of the conversion as it takes place.
See Section 6.2 for constraints on clock speed.
3.5
DOUT (Serial Data output)
The SPI serial data output pin is used to shift out the
results of the A/D conversion. Data will always change
on the falling edge of each clock as the conversion
takes place.
4.0
DEVICE OPERATION
The MCP3001 A/D converter employs a conventional
SAR architecture. With this architecture, a sample is
acquired on an internal sample/hold capacitor for
1.5 clock cycles starting on the first rising edge of the
serial clock after CS has been pulled low. Following this
sample time, the input switch of the converter opens
and the device uses the collected charge on the inter-
nal sample and hold capacitor to produce a serial 10-bit
digital output code. Conversion rates of 200 ksps are
possible on the MCP3001. See Section 6.2 for informa-
tion on minimum clock rates. Communication with the
device is done using a 3-wire SPI-compatible interface.
4.1
Analog Inputs
The MCP3001 provides a single pseudo-differential
input. The IN+ input can range from IN- to (V
REF +IN-).
The IN- input is limited to ±100 mV from the V
SS rail.
The IN- input can be used to cancel small signal com-
mon-mode noise which is present on both the IN+ and
IN- inputs.
For the A/D Converter to meet specification, the charge
holding capacitor, C
SAMPLE must be given enough time
to acquire a 10-bit accurate voltage level during the
1.5 clock cycle sampling period. The analog input
model is shown in Figure 4-1.
In this diagram, it is shown that the source impedance
(R
S) adds to the internal sampling switch, (RSS) imped-
ance, directly affecting the time that is required to
charge the capacitor, C
SAMPLE. Consequently, a larger
source impedance increases the offset, gain, and inte-
gral linearity errors of the conversion.
Ideally, the impedance of the signal source should be
near zero. This is achievable with an operational ampli-
fier such as the MCP601, which has a closed loop out-
put impedance of tens of ohms. The adverse affects of
higher source impedances are shown in Figure 4-2.
If the voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. If the voltage at IN+ is equal
to or greater than {[V
REF + (IN-)] - 1 LSB}, then the out-
put code will be 3FFh. If the voltage level at IN- is more
than 1 LSB below V
SS, then the voltage level at the IN+
input will have to go below V
SS to see the 000h output
code. Conversely, if IN- is more than 1 LSB above Vss,
then the 3FFh code will not be seen unless the IN+
input level goes above V
REF level.
4.2
Reference Input
The reference input (V
REF) determines the analog input
voltage range and the LSB size, as shown below.
As the reference input is reduced, the LSB size is
reduced accordingly. The theoretical digital output code
produced by the A/D Converter is a function of the ana-
log input signal and the reference input as shown
below.
where:
V
IN = analog input voltage = V(IN+) - V(IN-)
V
REF = reference voltage
When using an external voltage reference device, the
system designer should always refer to the manufac-
turer’s recommendations for circuit layout. Any instabil-
ity in the operation of the reference device will have a
direct effect on the operation of the ADC.
LSB Size
V
REF
1024
-------------
=
Digital Output Code
1024*V
IN
V
REF
------------------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2NV-CV-B1 | CONVERTER MOD DC/DC 5.8V 150W |
| B37937K9681J60 | CAP CER 680PF 16V 5% NP0 0603 |
| LT1016IS8#PBF | IC COMPARATOR 10NS HI-SPD 8-SOIC |
| VE-2NT-IW | CONVERTER MOD DC/DC 6.5V 100W |
| MCP3421A2T-E/CH | IC ADC 18BIT 3.75SPS 1CH SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3001T-I/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 10 BIT A/D CONVERTER WITH SPI SERIAL INTERFACE |
| MCP3001T-I/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 10 BIT A/D CONVERTER WITH SPI SERIAL INTERFACE |
| MCP3001T-I/SN | 功能描述:模数转换器 - ADC 10-bit SPI Sgl Chl IND TEMP, SOIC8 RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3001T-I/ST | 功能描述:模数转换器 - ADC 10-bit SPI Sgl Chl IND TEMP, TSSOP8 RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3002 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:MCP300X 10-Bit Analog-to-Digital Converters |
发布紧急采购，3分钟左右您将得到回复。