- 您现在的位置：买卖IC网 > PDF目录2159 > MCP6V11T-E/OT (Microchip Technology)IC OPAMP SGL ZERO DRIFT SOT23-5 PDF资料下载
参数资料
| 型号： | MCP6V11T-E/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 13/40页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP SGL ZERO DRIFT SOT23-5 |
| 标准包装： | 1 |
| 放大器类型： | 零漂移 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.03 V/µs |
| 增益带宽积： | 80kHz |
| 电流 - 输入偏压： | 5pA |
| 电压 - 输入偏移： | 8µV |
| 电流 - 电源： | 7.5µA |
| 电流 - 输出 / 通道： | 17mA |
| 电压 - 电源，单路/双路(±)： | 1.6 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | MCP6V11T-E/OTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MCP6V11/1U
DS25124A-page 20
2012 Microchip Technology Inc.
4.1.3
INTERMODULATION DISTORTION
(IMD)
These op amps will show intermodulation distortion
(IMD) products when an AC signal is present.
The signal and clock can be decomposed into sine
wave tones (Fourier series components). These tones
interact with the zero-drift circuitry’s non-linear
response to produce IMD tones at sum and difference
frequencies. Each of the square wave clock’s
harmonics has a series of IMD tones centered on it.
See Figure 2-36 and Figure 2-37.
4.2
Other Functional Blocks
4.2.1
RAIL-TO-RAIL INPUTS
The input stage of the MCP6V11/1U op amps uses two
differential CMOS input stages in parallel. One
operates at low common mode input voltage (VCM,
which is approximately equal to VIN+ and VIN– in
normal operation) and the other at high VCM. With this
topology, the input operates with VCM up to VDD +0.2V,
The input offset voltage (VOS) is measured at
VCM =VSS – 0.15V and VDD + 0.2V to ensure proper
operation.
The transition between the input stages occurs when
the best distortion and gain linearity, with non-inverting
gains, avoid this region of operation.
4.2.1.1
Phase Reversal
The input devices are designed to not exhibit phase
inversion when the input pins exceed the supply
voltages.
Figure 2-42 shows
an
input voltage
exceeding both supplies with no phase inversion.
4.2.1.2
Input Voltage Limits
In order to prevent damage and/or improper operation
of these amplifiers, the circuit must limit the voltages at
the input pins (see Section 1.1 “Absolute Maximum
). This requirement is independent of the
current limits discussed later on.
The ESD protection on the inputs can be depicted as
shown in Figure 4-4. This structure was chosen to
protect the input transistors against many (but not all)
overvoltage conditions, and to minimize input bias
current (IB).
FIGURE 4-4:
Simplified Analog Input ESD
Structures.
The input ESD diodes clamp the inputs when they try
to go more than one diode drop below VSS. They also
clamp any voltages that well above VDD; their
breakdown voltage is high enough to allow normal
operation, but not low enough to protect against slow
overvoltage (beyond VDD) events. Very fast ESD
events (that meet the spec) are limited so that damage
does not occur.
In some applications, it may be necessary to prevent
excessive voltages from reaching the op amp inputs;
Figure 4-5 shows one approach to protecting these
inputs. D1 and D2 may be small signal silicon diodes,
Schottky diodes for lower clamping voltages or diode
connected FETs for low leakage.
FIGURE 4-5:
Protecting the Analog Inputs
Against High Voltages.
Bond
Pad
Bond
Pad
Bond
Pad
VDD
VIN+
VSS
Input
Stage
Bond
Pad
VIN–
V1
VDD
D1
VOUT
V2
D2
U1
MCP6V1X
相关PDF资料 |
PDF描述 |
|---|---|
| MCP6V27T-E/SN | IC OPAMP DUAL AUTO-ZERO 8SOIC |
| MCP6V31UT-E/LT | IC OPAMP SGL ZERO DRIFT SC70-5 |
| ME50101VX-000U-A99 | FAN BRUSHLESS 12VDC 50X50X10MM |
| MIC6211BM5 TR | IC OP AMP GEN PURPOSE SOT23-5 |
| MIC7111BM5 TR | IC OPAMP R-R I/O 1.8V SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP6V11UT-E/LT | 功能描述:运算放大器 - 运放 Single, Zero Drift Op Amp, E Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MCP6V11UT-E/LT-CUT TAPE | 制造商:Microchip Technology 功能描述:Cut Tape 制造商:Microchip Technology 功能描述:SP Amp Zero Drift Amplifier Single R-R I/O 5.5V 5-Pin SC-70 T/R |
| MCP6V11UT-E/OT | 功能描述:运算放大器 - 运放 Single, Zero Drift Op Amp, E Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MCP6V11UT-E/OT-CUT TAPE | 制造商:Microchip Technology 功能描述:Cut Tape 制造商:Microchip Technology 功能描述:SP Amp Zero Drift Amplifier Single R-R I/O 5.5V 5-Pin SOT-23 T/R |
| MCP6V26-E/MS | 功能描述:运算放大器 - 运放 Single, Auto-Zero Op Amp, E Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。