参数资料
型号: MCW68332A
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, MICROCONTROLLER, UUC
封装: WAFER
文件页数: 30/111页
文件大小: 650K
代理商: MCW68332A
MC68332
MOTOROLA
MC68332TS/D
25
3.3.3 Clock Control
The clock control circuits determine system clock frequency and clock operation under special circum-
stances, such as following loss of synthesizer reference or during low-power operation. Clock source is
determined by the logic state of the MODCLK pin during reset.
When the on-chip clock synthesizer is used, system clock frequency is controlled by the bits in the upper
byte of SYNCR. Bits in the lower byte show status of or control operation of internal and external clocks.
The SYNCR can be read or written only when the CPU is operating at the supervisor privilege level.
W — Frequency Control (VCO)
This bit controls a prescaler tap in the synthesizer feedback loop. Setting the bit increases the VCO
speed by a factor of four. VCO relock delay is required.
X — Frequency Control Bit (Prescale)
This bit controls a divide by two prescaler that is not in the synthesizer feedback loop. Setting the bit
doubles clock speed without changing the VCO speed. There is no VCO relock delay.
Y[5:0] — Frequency Control (Counter)
The Y field controls the modulus down counter in the synthesizer feedback loop, causing it to divide by
a value of Y
+ 1. Values range from 0 to 63. VCO relock delay is required.
EDIV — E Clock Divide Rate
0 = ECLK frequency is system clock divided by 8.
1 = ECLK frequency is system clock divided by 16.
ECLK is an external M6800 bus clock available on pin ADDR23. Refer to 3.5 Chip Selects for more
information.
SLIMP — Limp Mode Flag
0 = External crystal is VCO reference.
1 = Loss of crystal reference.
When the on-chip synthesizer is used, loss of reference frequency causes SLIMP to be set. The VCO
continues to run using the base control voltage. Maximum limp frequency is maximum specified system
clock frequency. X-bit state affects limp frequency.
SLOCK — Synthesizer Lock Flag
0 = VCO is enabled, but has not locked.
1 = VCO has locked on the desired frequency (or system clock is external).
The MCU maintains reset state until the synthesizer locks, but SLOCK does not indicate synthesizer
lock status until after the user writes to SYNCR.
RSTEN — Reset Enable
0 = Loss of crystal causes the MCU to operate in limp mode.
1 = Loss of crystal causes system reset.
STSIM — Stop Mode SIM Clock
0 = When LPSTOP is executed, the SIM clock is driven from the crystal oscillator and the VCO is
turned off to conserve power.
1 = When LPSTOP is executed, the SIM clock is driven from the VCO.
STEXT — Stop Mode External Clock
0 = When LPSTOP is executed, the CLKOUT signal is held negated to conserve power.
1 = When LPSTOP is executed, the CLKOUT signal is driven from the SIM clock, as determined by
the state of the STSIM bit.
SYNCR —Clock Synthesizer Control Register
$YFFA04
15
14
13
8
7
6
5
4
3
2
1
0
W
X
Y
EDIV
0
SLIMP
SLOCK RSTEN
STSIM
STEXT
RESET:
0
1
0
U
0
相关PDF资料
PDF描述
MC68EN360CEM25L 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP240
M30626FJPGP 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP100
M30302MC-XXXGP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M37542F8TGP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
M37542M4-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36
相关代理商/技术参数
参数描述
MCW-70A 制造商:SPC Multicomp 功能描述:WATERPROOF COVER BLACK TOGGL 制造商:SPC Multicomp 功能描述:WATERPROOF COVER, BLACK, TOGGLE SWITCH; For Use With:20mm Lever Height Toggle Switches; Actuator / Cap Color:Black
MCW-70B 制造商:SPC Multicomp 功能描述:WATERPROOF COVER BLACK TOGGL 制造商:SPC Multicomp 功能描述:WATERPROOF COVER, BLACK, TOGGLE SWITCH; For Use With:20mm Lever Height Toggle Switches; Actuator / Cap Color:Black
MCW74HC4851ATR DIE 制造商:ON Semiconductor 功能描述:
MCWF06R1000BTL 制造商:SPC Multicomp 功能描述:RESISTOR 0603 100R 0.1% 0.
MCWF06R1001BTL 制造商:SPC Multicomp 功能描述:RESISTOR 0603 1K 0.1% 0.1W