参数资料
| 型号： | MCZ33390EF |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 4/15页 |
| 文件大小： | 0K |
| 描述： | IC TXRX SERIAL LINK 8-SOIC |
| 标准包装： | 98 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | J-1850 |
| 电源电压： | 9 V ~ 16 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
Analog Integrated Circuit Device Data
12
Freescale Semiconductor
33390
TYPICAL APPLICATIONS
“start of frame” bit has been transmitted, the secondary node
transmitting the most consecutive logic [0] bits will be granted
sole transmission access to the bus for that message.
Loss of Assembly Ground Connection
The definition of a loss of assembly ground condition at the
device level is that all pins of the 33390, with the exception of
BUS and LOAD, see a very low impedance to VBAT.
The LOAD pin of the device has an internal transistor
switch connected to it that is normally saturated to ground.
This pulls the LOAD-side of the external resistor (tied from
BUS to LOAD) to ground under normal conditions. The LOAD
pin switch is essentially that of an “upside down” FET, which
is normally biased “on” so long as module ground is present
and biased “off” when loss-of-ground occurs. When a loss of
assembly ground occurs, the load transistor switch is self-
biased “off”, allowing no more than 100 A of leakage current
to flow in the LOAD pin. During such a loss of assembly
ground condition, the BUS and LOAD pins exhibit a high
impedance to VBAT; all other pins will exhibit a low
impedance to VBAT. During this condition the BUS pin is
prevented from sourcing any current or loading the bus,
which would cause a corruption of any data being transmitted
on the bus. While a particular assembly is experiencing a loss
of ground, all other assembly nodes are permitted to function
normally. It should be noted that with other nodes existing on
the bus, the bus will always have some minimum/maximum
impedance to ground as shown in Table 5, page 10.
Loss of Assembly Battery Connection
The definition of a loss of assembly battery condition at the
device level is that the VBAT pin of the 33390 sees an infinite
impedance to VBAT, but there is some undefined impedance
between these pins and ground.
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33897DEFR2 | IC TXRX SGL WIRE CAN 8-SOIC |
| MIC1555BM5 TR | IC OSC MONO TIMING 5MHZ SOT23-5 |
| MK1491-09FTR | IC CLK SRC AMD GEODE GX2 28-SSOP |
| MK1574-01BSILF | IC PLL FRAME RATE COMM 16-SOIC |
| MK1575-01GILF | IC CLK RECOVERY PLL 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33390EFR2 | 功能描述:网络控制器与处理器 IC J1850 SERIAL TRANSCEIVER RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33395EW | 功能描述:马达/运动/点火控制器和驱动器 3 PHASE MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33395EWR2 | 功能描述:马达/运动/点火控制器和驱动器 3 PHASE MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33399EF | 功能描述:输入/输出控制器接口集成电路 LIN INTERFACE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33399EFR2 | 功能描述:输入/输出控制器接口集成电路 LIN INTERFACE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。