参数资料
| 型号： | MCZ33810EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 25/37页 |
| 文件大小： | 0K |
| 描述： | IC IGNITION INJECTOR 32-SOIC |
| 标准包装： | 42 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 4.5 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Each gate driver is individually set to either, restore to the
Table 14. FBx Fault Threshold Select
pre-fault state, or shutdown when a short fault is declared. By
GPGD V DS FLT
Bits
000
001
010
011
100
101
110
111
FBx Fault Threshold Select
0.5V
1.0V
1.5V
2.0 (default)
2.5V
3.0V
No Change
No Change
setting the Retry/Shutdown bit in the GPGD Fault Operation
Command to logic 1 the specific output will try to go back to
the pre-fault state when the fault is no longer declared, after
a programmed “inhibit time”.
The retry strategy will cause the output to try to return to
the pre-fault state on a 1% duty cycle basis. For example: If
the fault timer is set to 120 μ s and a fault is declared (drain
voltage greater than the programmed threshold for greater
than 120 μ s), the GDx output driver will be forced off for 12ms.
After 12ms has elapsed, if the inputs, GINx or SPI, have not
tried to shut off the particular GDx output in the interim, the
GDx output will try to set the external driver on again (the pre-
fault state). A continued declared fault on the output would
result in another 12ms shutdown period.
By setting the Retry/Shutdown bit in the GPGD Fault
Operation Command to logic 0 the specific output will
shutdown and remain off when the short fault is declared.
Fault Timer Select
GPGD SHORT TIMER COMMAND
The GPGD Short Timer Command allows the user to
select the duration of time that the drain voltage is allowed to
be greater than the programed threshold voltage without
causing shutdown. External MOSFETS with drain voltages
greater than the programed threshold for longer than the
Fault Duration Timer are shutdown. Timer durations are listed
Table 15. FBx Short Fault Timer
GPGD FLT Timer
Bits
Only a reissue of the turn on command, via SPI or GINx, will
force the output to try and turn on again.
In the event that a GPGD is selected as a PWM controller
and a short occurs on the output, the output retry strategy
forces the output to a 1% duty cycle based on the fault timer
setting. For example: If the fault timer is set to 120 μ s and a
fault is detected (drain voltage greater than programmed
threshold), the PWM output will be commanded off for 12ms
and commanded ON again at the next PWM cycle.
Care should be taken to select a fault timer that is shorter
than the minimum duty cycle ON time of the PWM controller.
Selecting a fault timer that is longer will allow the PWM
controller to continue to drive the external MOSFET into a
000
001
010
011
100
101
110
111
30μs
60μs
120μs
240μs (default)
480μs
960μs
No Change
No Change
shorted load.
PWM FREQUENCY/DUTY CYCLE COMMAND
The PWMx Freq & Duty Cycle command is use to program
the GDx outputs with a frequency and duty cycle. Table 16
defines the user selectable output frequency. The frequency
and duty cycle may be updated at any time using the PWM
Freq&DC command, however the update will only begin on
the next PWM rising edge time.
Once the PWM Freq & DC registers are programmed and
the PWM controller is enabled through the Mode Command
the PWM outputs are turned ON and OFF via the GINx pin
OR the SPI GPGD ON/OFF Command control bit. All Parallel
Notes: Tolerance on this fault timer setting is ±10% after using the
Calibration Command.
GPGD FAULT OPERATION COMMAND
The GPGD Fault Operation Command sets the operating
parameters for the gate drivers under faulted conditions. A
short fault is said to be “detected” when the drain source
voltage, Vds, of the external MOSFET, exceeds the SPI
programmed short threshold voltage. The short fault is said
to be “declared” when the V DS over-voltage lasts longer than
the SPI programmed “fault timer.” (short duration time > fault
and serial On and Off command updates to the PWM
controller are synchronous with the rising edge of the
previous PWM period.
The truth table for GDx control in general purpose mode is
The duty cycle of the PWM outputs is controlled by bits 0-
6, inclusive. The duty cycle value is 1% per binary count from
1-100 with counts of 101-127 defaulting to 100%. For
example, sending SPI command 101001000001100 would
set GD1, PWM output to 10Hz and 12% duty cycle.
timer programmed value)
33810
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33812AEKR2 | IC DVR IGNITION/INJECTOR 32SOIC |
| MCZ33812EKR2 | IC DVR IGNITION/INJECTOR 32-SOIC |
| MCZ33879EKR2 | IC SWITCH HI/LO SIDE 16B 32-SOIC |
| MCZ33991EGR2 | IC GAUGE DRIVER SPI 24-SOIC |
| MCZ34702EWR2 | IC PWR SUPPLY 3A SW 32-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
| MCZ33810EKR2 | 功能描述:马达/运动/点火控制器和驱动器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33810R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC Quad injector driver with Parallel/SPI control |
| MCZ33811EG | 功能描述:电流和电力监控器、调节器 SOLENOID MONITOR IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MCZ33811EGR2 | 功能描述:电流和电力监控器、调节器 SOLENOID MONITOR IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。