- 您现在的位置：买卖IC网 > PDF目录95942 > MGSF2P02HDR2 (MOTOROLA INC) 1.3 A, 20 V, 0.175 ohm, P-CHANNEL, Si, POWER, MOSFET PDF资料下载
参数资料
| 型号： | MGSF2P02HDR2 |
| 厂商： | MOTOROLA INC |
| 元件分类： | JFETs |
| 英文描述： | 1.3 A, 20 V, 0.175 ohm, P-CHANNEL, Si, POWER, MOSFET |
| 封装： | PLASTIC, TSOP-6 |
| 文件页数： | 7/8页 |
| 文件大小： | 179K |
| 代理商： | MGSF2P02HDR2 |
MGSF2P02HD
7
Motorola TMOS Power MOSFET Transistor Device Data
INFORMATION FOR USING THE TSOP–6 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
inches
1.9
0.039
1.0
0.094
0.7
0.074
2.4
0.028
0.95
0.037
0.95
0.037
TSOP–6
TSOP–6 POWER DISSIPATION
The power dissipation of the TSOP–6 is a function of the
drain pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, R
θJA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the TSOP–6 package,
PD can be calculated as follows:
PD =
TJ(max) – TA
R
θJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one can
calculate the power dissipation of the device which in this
case is 400 milliwatts.
PD =
150
°C – 25°C
312
°C/W
= 400 milliwatts
The 312
°C/W for the TSOP–6 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 400 milliwatts. There
are other alternatives to achieving higher power dissipation
from the TSOP–6 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad
. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°C.
The soldering temperature and time shall not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相关PDF资料 |
PDF描述 |
|---|---|
| MGSF3441VT1 | 3300 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MGSF3441XT3 | 1500 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MGSF3441XT1 | 1500 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MGSF3442VT1 | 4 A, 20 V, 0.07 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MGSF3442VT3 | 0.07 ohm, Si, POWER, FET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MGSF2P02HDT1 | 制造商:ON Semiconductor 功能描述:Trans MOSFET P-CH 20V 2.9A 6-Pin TSOP T/R |
| MGSF2P02HDT3 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power MOSFET 2 Amps, 20 Volts |
| MGSF3433VT1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MGSF3441VT1 | 制造商:ON Semiconductor 功能描述:Trans MOSFET P-CH 20V 3.3A 6-Pin TSOP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MGSF3441VTD | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:Low rDS(on) Small-signal MOSFETs TMOS Single P=Channel Field Effect Transistors |
发布紧急采购，3分钟左右您将得到回复。