- 您现在的位置：买卖IC网 > PDF目录19851 > MIC2310-1ZTS TR (Micrel Inc)IC HOT SWAP CTLR 2CHAN 24TSSOP PDF资料下载
参数资料
| 型号： | MIC2310-1ZTS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 4/34页 |
| 文件大小： | 473K |
| 描述： | IC HOT SWAP CTLR 2CHAN 24TSSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 10.8 V ~ 13.2 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Micrel, Inc.
MIC2310
July 2008
4
M9999-070108-A
Pin Description
Pin Number
Pin Name
Pin Function
1
UVLO
Undervoltage Lockout Input. When the applied voltage at the UVLO pin is higher
than the controllers V
UVLOH
threshold voltage, the GATE drive circuits are active
when ENABLE= HIGH. If the applied voltage at the UVLO pin falls below the
controllers V
UVLOL
threshold voltage, the GATE drive circuits are disabled to turn
the external MOSFET OFF. In addition, the DISCH circuit is activated to drive an
optional, external discharge transistor alone (illustrated in the Typical Application
circuit) or in combination with an SCR for a very fast discharge circuit
configuration.
2
OVP
Overvoltage Protection Input. When the applied voltage at the OVP pin is higher
than the controllers V
OVPH
threshold voltage, the GATE drive circuit is disabled
to turn the external MOSFET OFF. In addition, the DISCH circuit is activated to
drive an optional, external discharge transistor alone (illustrated in the Typical
Application circuit) or in combination with an SCR for a very fast discharge circuit
configuration. Using an external resistor divider, the UVLO and the OVP pins
form a window comparator that defines the supply voltage range within which the
load may be safely powered.
3
VISS
Steady-state Output Current Monitor. This output signal provides an analog
voltage that is proportional to the steady-state load current. This signal is
provided as an input to the system supervisor/processor to monitor the dc
current/power level of the application circuit.
4
VREG
Internal +5V Regulator Bypass. Connect a 0.1-礔, 16V ceramic capacitor from
this pin to AGND.
5
NC
No connection
6
ENABLE
ENABLE Input. An active asserted-HIGH digital input that controls the operation
of the MIC2310. Activated after the internal POR timer has terminated, a LOW-
to-HIGH transition on this pin commences a start-up sequence if the applied V
CC
is above the V
UVLOH
and below the V
OVPH
threshold voltages. While ENABLE =
LOW, the GATE pin is held to 0V and the DISCH output is activated. The
ENABLE input can be used to reset the internal circuit breaker by applying a
HIGH-to-LOW-to-HIGH transition as defined by t
ENLPW
following either a load
current fault, an open LOADSENSE fault, an open GNDSENSE fault, or a
shorted RSENSE fault.
7
S0
8
S1
Secondary OC Detector Current Threshold Digital Inputs S1 is the MSB and
S0 is the LSB. When used together, S[1:0] sets the overcurrent threshold for the
secondary overcurrent detection circuit to one of four levels relative to the
primary overcurrent detector nominal threshold. For example, S[1:0] = L, L sets
the secondary overcurrent threshold at 1.3X; S[1:0] = L, H sets a 1.5X threshold;
S[1:0] = H, L sets a 2X threshold, and S[1:0] = H, H sets a 1.75X threshold. If the
S[1:0] pins are not connected or left NC, the default setting is S[1:0] = L, L or
1.3X. The permissible voltage range on these inputs is AGND d S[1:0] d V
CC
.
9
CRETRY
Auto-retry Timing Capacitor. A capacitor connected from the CRETRY pin to
AGND configures the MIC2310 to re-start automatically with ENABLE = HIGH
after the circuit breaker trips and latches off. It also sets the cool-off time delay
before a new load current start-up sequence is initiated. To configure the
MIC2310s circuit breaker to latch off after fault, connect this pin to AGND. The
circuit breaker latches OFF and remains latched OFF unless the ENABLE input
is toggled HIGH-to-LOW-to-HIGH as defined by t
ENLPW
or the V
CC
supply voltage
is turned OFF then ON.
10
CPRIMARY Primary Overcurrent Detector Timing Capacitor. Connecting a capacitor from the
CPRIMARY pin to AGND sets the response time of the controllers primary
overcurrent detection circuit to GATE OFF in the event of an overcurrent
condition. If the CPRIMARY pin is not connected, the primary overcurrent
detection response time defaults to t
POCSENSE
, typically 250祍 as specified in the
Electrical Characteristics Table. The controller incorporates a patent-pending
built-in test for a faulty CPRIMARY capacitor.
相关PDF资料 |
PDF描述 |
|---|---|
| GRM2195C2A910JZ01D | CAP CER 91PF 100V 5% NP0 0805 |
| HBC06DRYI | CONN EDGECARD 12POS DIP .100 SLD |
| 5650092-1 | CONN ASSY DUAL POS .050 |
| RSC36DRTN-S734 | CONN EDGECARD 72POS DIP .100 SLD |
| TIM106M015P0Y | CAP TANT 10UF 15V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2310-2ZTS | 功能描述:热插拔功率分布 Single Channel, Positive Voltage, Constant Power-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2310-2ZTS TR | 功能描述:热插拔功率分布 Single Channel, Positive Voltage, Constant Power-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC23150-4YMT EV | 功能描述:电源管理IC开发工具 2.0A 4MHz HyperLight Load Buck Regulator - Evaluation Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MIC23150-4YMT TR | 功能描述:直流/直流开关调节器 2.0A 4MHz HyperLight Load Buck Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC23150-4YMT-TR | 功能描述:Buck Switching Regulator IC Positive Fixed 1.2V 1 Output 2A 8-VFDFN Exposed Pad, 8-MLF? 制造商:microchip technology 系列:HyperLight Load? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.7V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:1.2V 电压 - 输出（最大值）:- 电流 - 输出:2A 频率 - 开关:4MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。