- 您现在的位置：买卖IC网 > PDF目录132963 > MJ80C52XXX-12 (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 12 MHz, MICROCONTROLLER, QCC44 PDF资料下载
参数资料
| 型号： | MJ80C52XXX-12 |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, QCC44 |
| 封装： | LCC-44 |
| 文件页数： | 105/108页 |
| 文件大小： | 3682K |
| 代理商： | MJ80C52XXX-12 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页当前第105页第106页第107页第108页
96
8069R–AVR–06/2013
XMEGA A4
Not recommended for new designs -
Use XMEGA A4U series
Problem fix/Workaround
Do not set the BOD level higher than VCC even if the BOD is not used.
11. Sampled BOD in Active mode will cause noise when bandgap is used as reference
Using the BOD in sampled mode when the device is running in Active or Idle mode will add
noise on the bandgap reference for ADC, DAC and Analog Comparator.
Problem fix/Workaround
If the bandgap is used as reference for either the ADC, DAC or the Analog Comparator, the
BOD must not be set in sampled mode.
12. DAC is nonlinear and inaccurate when reference is above 2.4V or VCC - 0.6V
Using the DAC with a reference voltage above 2.4V or VCC - 0.6V will give inaccurate out-
put when converting codes that give below 0.75V output:
– ±10 LSB for continuous mode
– ±200 LSB for Sample and Hold mode
Problem fix/Workaround
None.
13. DAC has increased INL or noise for some operating conditions
Some DAC configurations or operating condition will result in increased output error.
– Continous mode: ±5 LSB
– Sample and hold mode: ±15 LSB
– Sample and hold mode for reference above 2.0v: up to ±100 LSB
Problem fix/Workaround
None.
14. EEPROM page buffer always written when NVM DATA0 is written
If the EEPROM is memory mapped, writing to NVM DATA0 will corrupt data in the EEPROM
page buffer.
Problem fix/Workaround
Before writing to NVM DATA0, for example when doing software CRC or flash page buffer
write, check if EEPROM page buffer active loading flag (EELOAD) is set. Do not write NVM
DATA0 when EELOAD is set.
15. Pending full asynchronous pin change interrupts will not wake the device
Any full asynchronous pin-change Interrupt from pin 2, on any port, that is pending when the
sleep instruction is executed, will be ignored until the device is woken from another source
or the source triggers again. This applies when entering all sleep modes where the System
Clock is stopped.
Problem fix/Workaround
None.
16. Pin configuration does not affect Analog Comparator output
The Output/Pull and inverted pin configuration does not affect the Analog Comparator
output.
Problem fix/Workaround
None for Output/Pull configuration.
相关PDF资料 |
PDF描述 |
|---|---|
| MJ80C52XXX-36/883 | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, QCC44 |
| MK10N512VLL100R | FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP100 |
| MPC8271CVRMIBX | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA516 |
| M306NMFJTGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP128 |
| MPC8260CZUGIAXXX | 32-BIT, 150 MHz, RISC PROCESSOR, PBGA480 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MJ8100 | 制造商:ASI 功能描述:8100 N11E4C |
| MJ8100R | 制造商:SEME-LAB 制造商全称:Seme LAB 功能描述:Bipolar PNP Device in a Hermetically sealed TO39 |
| MJ-82-1 | 制造商:SPC Multicomp 功能描述:SOCKET PCB DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER; Gender:Receptacle; Connector Mounting:PCB; Contact Termination:Through Hole Vertical; Connector Mounting Orientation:PCB; Connector Type:Standard Power Entry ;RoHS Compliant: Yes |
| MJ8250FE | 制造商:Ohmite Mfg Co 功能描述: |
| MJ8251F | 制造商:Ohmite Mfg Co 功能描述: |
发布紧急采购，3分钟左右您将得到回复。