- 您现在的位置：买卖IC网 > PDF目录132963 > MJ80C52XXX-12 (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 12 MHz, MICROCONTROLLER, QCC44 PDF资料下载
参数资料
| 型号： | MJ80C52XXX-12 |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, QCC44 |
| 封装： | LCC-44 |
| 文件页数： | 107/108页 |
| 文件大小： | 3682K |
| 代理商： | MJ80C52XXX-12 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页当前第107页第108页
98
8069R–AVR–06/2013
XMEGA A4
Not recommended for new designs -
Use XMEGA A4U series
23. Clearing TWI Stop Interrupt Flag may lock the bus
If software clears the STOP Interrupt Flag (APIF) on the same Peripheral Clock cycle as the
hardware sets this flag due to a new address received, CLKHOLD is not cleared and the
SCL line is not released. This will lock the bus.
Problem fix/Workaround
Check if the bus state is IDLE. If this is the case, it is safe to clear APIF. If the bus state is
not IDLE, wait for the SCL pin to be low before clearing APIF.
Code:
/* Only clear the interrupt flag if within a "safe zone". */
while ( /* Bus not IDLE: */
((COMMS_TWI.MASTER.STATUS & TWI_MASTER_BUSSTATE_gm) !=
TWI_MASTER_BUSSTATE_IDLE_gc)) &&
/* SCL not held by slave: */
!(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm)
)
{
/* Ensure that the SCL line is low */
if ( !(COMMS_PORT.IN & PIN1_bm) )
break;
}
/* Check for an pending address match interrupt */
if ( !(COMMS_TWI.SLAVE.STATUS & TWI_SLAVE_CLKHOLD_bm) )
{
/* Safely clear interrupt flag */
COMMS_TWI.SLAVE.STATUS |= (uint8_t)TWI_SLAVE_APIF_bm;
}
24. TWI START condition at bus timeout will cause transaction to be dropped
If Bus Timeout is enabled and a timeout occurs on the same Peripheral Clock cycle as a
START is detected, the transaction will be dropped.
Problem fix/Workaround
None.
25. TWI Data Interrupt Flag erroneously read as set
When issuing the TWI slave response command CMD=0b11, it takes 1 Peripheral Clock
cycle to clear the data interrupt flag (DIF). A read of DIF directly after issuing the command
will show the DIF still set.
Problem fix/Workaround
Add one NOP instruction before checking DIF.
26. WDR instruction inside closed window will not issue reset
When a WDR instruction is execute within one ULP clock cycle after updating the window
control register, the counter can be cleared without giving a system reset.
Problem fix/Workaround
Wait at least one ULP clock cycle before executing a WDR instruction.
相关PDF资料 |
PDF描述 |
|---|---|
| MJ80C52XXX-36/883 | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, QCC44 |
| MK10N512VLL100R | FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP100 |
| MPC8271CVRMIBX | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA516 |
| M306NMFJTGP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP128 |
| MPC8260CZUGIAXXX | 32-BIT, 150 MHz, RISC PROCESSOR, PBGA480 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MJ8100 | 制造商:ASI 功能描述:8100 N11E4C |
| MJ8100R | 制造商:SEME-LAB 制造商全称:Seme LAB 功能描述:Bipolar PNP Device in a Hermetically sealed TO39 |
| MJ-82-1 | 制造商:SPC Multicomp 功能描述:SOCKET PCB DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER; Gender:Receptacle; Connector Mounting:PCB; Contact Termination:Through Hole Vertical; Connector Mounting Orientation:PCB; Connector Type:Standard Power Entry ;RoHS Compliant: Yes |
| MJ8250FE | 制造商:Ohmite Mfg Co 功能描述: |
| MJ8251F | 制造商:Ohmite Mfg Co 功能描述: |
发布紧急采购，3分钟左右您将得到回复。