- 您现在的位置：买卖IC网 > PDF目录98023 > MM908E621ACDWB (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 PDF资料下载
参数资料
| 型号： | MM908E621ACDWB |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| 封装： | 17.90 X 7.50 MM, 0.65 MM PITCH, PLASTIC, SOIC-54 |
| 文件页数： | 35/62页 |
| 文件大小： | 917K |
| 代理商： | MM908E621ACDWB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Analog Integrated Circuit Device Data
40
Freescale Semiconductor
908E621
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Table 10. High-Side Configuration Bits
High-Side Overvoltage / Undervoltage Protection
The outputs are protected against under- / overvoltage
conditions. This protection is done by the low and high
voltage interrupt circuitry. If an over- under voltage condition
is detected (LVIF / HVIF) and Bit VIS in the High-Side Status
Register is cleared, the output is disabled.
The over- / undervoltage status flags are cleared (and the
output reenabled) by writing a logic [1] to the LVIF / HVIF
flags in the Interrupt Flag Register or by reset. Clearing this
flag has no effect as long as a high or low voltage condition
is present.
HIGH-SIDE OVERTEMPERATURE PROTECTION
The outputs are protected against over temperature
conditions.
Each power output comprises two different temperature
thresholds.
The first threshold is the high temperature interrupt (HTI),
if the temperature reach this threshold the HTI bit in the
interrupt flag register is set and an interrupt will be generated
if HTIE bit in the interrupt mask register is set. In addition this
interrupt can be used to automatically turn off the power
stages (all high-sides, on Half bridges just the high-side
FET’s). This shutdown can be enabled/disabled by Bit
HTIS0.
The high temperature interrupts flag (HTIE) is cleared (and
the outputs reenabled) by writing a logic [1] to the HTIF flag
in the Interrupt Status Register or by reset. Clearing this flag
has no effect as long as a high temperature condition is
present.
If the HTIS shutdown is disabled, a second threshold
(HTR) will be used to turn off all power stages (HB (all Fet’s),
HS, HVDD, H0) in order to protect the device.
High-Side Overcurrent Protection
The HS outputs are protected against overcurrent. When
the overcurrent limit is reached, the output will be
automatically switched off and the overcurrent flag is set.
Due to the high inrush current of bulbs a special feature
was implemented to avoid a overcurrent shutdown during this
inrush current. If a PWM frequency will be supplied to the
PWM input during the switch on of a bulb, the inrush current
will be limited to the overcurrent shutdown limit. This means,
if the current reaches the overcurrent shutdown, the high-
side will be switched off, but each rising edge on the PWM
input will enable the driver again. The duty cycle supplied by
the MCU has no influence on the switch-on time of the high-
side driver.
In order to distinguish between a shutdown due to an
inrush current or a real shutdown, the software has to check
if the overcurrent status flag (HSxOCF) in the High-Side
Status register is set beyond a certain period of time.
HSxPWM
HSxON
Mode
0
High-side MOSFET off
0
1
High-side MOSFET on, in case of overcurrent
the overcurrent flag (HSxOCF) is set and the
High-side MOSFET is turned off
1
0
In this mode the PWM duty cycle is either
controlled by the PWM input signal or in case
the overcurrent shutdown value is reached by
the part itself.
Without reaching the overcurrent shutdown,
the high-side driver is directly driven from the
PWM input signal. If the Input signal is high the
output is on, if low the output is off (PWM
control).
If the current reaches the overcurrent
shutdown value, the high-side will be
automatically turned off, with the next rising
edge of the PWM input signal the output will
turn on again (current limitation). The HSxOCF
bit will be set, software has to distinguish
between an inrush current and a real short on
the output.
1
High-side MOSFET is switched on and the
inrush current limitation is enabled, means the
high side will start automatically with an
current limitation around the overcurrent
shutdown threshold. (PWM signal must be
applied, see Figure 24)
If the high-side enters current limitation the
HSxOCF bit is set, but the output is not
disabled. The software needs to take care
about distinguish between an inrush current
and a real short on the output.
相关PDF资料 |
PDF描述 |
|---|---|
| MM908E622ACDWB/R2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E624ACDWB/R | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E625ACDWB | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MMBD1010LT3 | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBD3000T1 | 0.2 A, SILICON, SIGNAL DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E621ACDWB/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge and Triple High Side with Embedded MCU and LIN for High End Mirror |
| MM908E621ACDWBR2 | 功能描述:8位微控制器 -MCU QUAD HB / TRIPLE HS 841B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E621ACPEK | 功能描述:8位微控制器 -MCU QUAD H-B/3-HS W/MCU & LI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E621ACPEKR2 | 功能描述:8位微控制器 -MCU QUAD HB AND TRIPLE HS RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E622 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
发布紧急采购，3分钟左右您将得到回复。