- 您现在的位置：买卖IC网 > PDF目录3922 > MM908E622ACDWB (Freescale Semiconductor)IC QUAD HALF BRDG TRPL SW 54SOIC PDF资料下载
参数资料
| 型号： | MM908E622ACDWB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 20/63页 |
| 文件大小： | 0K |
| 描述： | IC QUAD HALF BRDG TRPL SW 54SOIC |
| 标准包装： | 26 |
| 应用： | 自动镜像控制 |
| 核心处理器： | HC08 |
| 程序存储器类型： | 闪存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 输入/输出数： | 12 |
| 电源电压： | 9 V ~ 16 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 54-SOICW-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
908E622
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
OPERATING MODES OF THE MCU
For a detailed description of the operating modes of
the MCU, refer to the MC68HC908EY16 datasheet.
INTERRUPTS
The 908E622 has seven different interrupt sources. An
interrupt pulse on the IRQ_A pin is generated to report an
event or fault to the MCU. All interrupts are maskable and can
be enabled/disabled via the SPI (Interrupt Mask Register).
After reset all interrupts are automatically disabled.
Low Voltage Interrupt
Low voltage interrupt (LVI) is related to external supply
voltage VSUP. If this voltage falls below the LVI threshold, it
will set the LVIF bit in the Interrupt Flag Register. In case the
low voltage interrupt is enabled (LVIE = 1), an interrupt will be
initiated.
During Sleep and Stop mode the low voltage interrupt
circuitry is disabled.
High Voltage Interrupt
The high voltage interrupt (HVI) is related to the external
supply voltage VSUP. If this voltage rises above the HVI
threshold, it will set the HVIF bit in the Interrupt Flag Register.
If the high voltage interrupt is enabled (HVIE = 1), an interrupt
will be initiated.
During Stop and Sleep mode the HVI circuitry is disabled.
High Temperature Interrupt
The high temperature interrupt (HTI) is generated by the
on chip temperature sensors. If the chip temperature is above
the HTI threshold, the HTIF bit in the Interrupt Flag Register
will be set. If the high temperature interrupt is enabled (HTIE
= 1), an interrupt will be initiated.
During Stop and Sleep mode the HTI circuitry is disabled.
LIN Interrupt
The LIN Interrupt is related to the Stop mode. If the LIN
interrupt is enabled (LINIE = 1) in Stop mode, an interrupt is
asserted if a rising edge is detected, and the bus was
dominant longer than tPROPWL. After the wake-up / interrupt,
the LINIF is indicating the reason for the wake-up / interrupt.
Power Stage Fail Interrupt
The power stage fail flag indicates an error condition on
In case the power stage fail interrupt is enabled (PSFIE =
1), an interrupt will be initiated if:
During Stop and Sleep mode, the PSFI circuitry is
disabled.
HO Input Interrupt
The H0 interrupt flag H0IF is set in run mode by a state
change of the H0F flag (rising or falling edge on the enabled
input). The interrupt function is available if the input is
selected as General Purpose, or as 2-pin Hall sensor input.
The interrupt is maskable with the H0IE bit in the Interrupt
Mask Register.
During Stop and Sleep mode the H0I circuitry is disabled.
Table 6. Operating Modes Overview
Device Mode
Voltage Regulator
Wake-up Capabilities
RST_A
Output
MCU monitoring/
Watchdog Function
Power Stages
LIN Interface
Reset
VDD ON
N/A
LOW
Disabled
Normal Request
VDD ON
N/A
HIGH
tNORMREQ (80 ms
typical) time out to
set PSON bit in
System Control
Register
Disabled
Normal (Run)
VDD ON
N/A
HIGH
Window Watchdog
active if enabled
Enabled
Stop
VDD ON with limited
current capability
LIN wake-up,
L0 state change
(SPI PSON=1)(33)
HIGH
Disabled
Recessive state with
wake-up capability
Sleep
VDD OFF
LIN wake-up
L0 state change
LOW
Disabled
Recessive state with
wake-up capability
Notes
33.
The SPI is still active in Stop mode. However, due to the limited current capability of the voltage regulator in Stop mode, the PSON bit
has to be set before the increased current caused from a running MCU causes an LVR.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2502S+T&R | IC OTP 1KBIT 8SOIC |
| AYF534965 | CONN SOCKET FPC 0.5MM 49POS SMD |
| DS2430A+T&R | IC EEPROM 256BIT TO92-3 |
| AYF534865 | CONN SOCKET FPC 0.5MM 48POS SMD |
| DS2502G+U | IC ADD-ONLY MEMORY 1KB SFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E622ACDWBR2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge, Triple High Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
| MM908E622ACEK | 功能描述:8位微控制器 -MCU QUAD H-B TRIHS EC GLASS RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E622ACPEK | 功能描述:IC QUAD HALF BRDG TRPL SW 54SOIC RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器 - 特定应用 系列:- 产品变化通告:Product Discontinuation 26/Aug/2009 标准包装:250 系列:- 应用:网络处理器 核心处理器:4Kc 程序存储器类型:- 控制器系列:- RAM 容量:16K x 8 接口:以太网，UART，USB 输入/输出数:- 电源电压:1.8V, 3.3V 工作温度:- 安装类型:表面贴装 封装/外壳:208-LQFP 包装:带卷 (TR) 供应商设备封装:PG-LQFP-208 其它名称:SP000314382 |
| MM908E622ACPEKR2 | 功能描述:8位微控制器 -MCU QUAD H-B, TRIHS, EC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E624 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TRIPLE HIGH-SIDE SWITCH WITH EMBEDDED MCU AND LIN |
发布紧急采购，3分钟左右您将得到回复。