参数资料
型号: MSC1201Y3RHHRG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQCC36
封装: GREEN, PLASTIC, QFN-36
文件页数: 24/93页
文件大小: 1093K
代理商: MSC1201Y3RHHRG4
MSC1200
MSC1201
MSC1202
SBAS317E APRIL 2004 REVISED MAY 2006
www.ti.com
30
SPI
The MSC120x implement a basic SPI interface that
includes the hardware for simple serial data transfers.
Figure 17 shows a block diagram of the SPI. The
peripheral supports master and slave modes, full duplex
data transfers, both clock polarities, both clock phases, bit
order, and slave select.
The timing diagram for supported SPI data transfers is
shown in Figure 18.
The I/O pins needed for data transfer are Data In (DIN),
Data Out (DOUT) and serial clock (SCK). The slave select
(SS) pin can also be used to control the output of data on
DOUT.
The DIN pin is used for shifting data in for both master and
slave modes.
The DOUT pin is used for shifting data out for both master
and slave modes.
The SCK pin is used to synchronize the transfer of data for
both master and slave modes. SCK is always generated
by the master. The generation of SCK in master mode can
be done either in software (by simply toggling the port pin),
or by configuring the output on the SCK pin via PASEL
(SFR F2h). A list of the most common methods of
generating SCK follows, but the complete list of clock
sources can be found by referring to the PASEL SFR.
D Toggle SCK by setting and clearing the port pin.
D Memory Write Pulse (WR) that is idle high.
Whenever an external memory write command
(MOVX) is executed, a pulse is seen on P3.6. This
method can be used only if CPOL is set to ‘1’.
D Memory Write Pulse toggle version. In this mode,
SCK toggles whenever an external write command
(MOVX) is executed.
D T0_Out signal can be used as a clock. A pulse is
generated on SCK whenever Timer 0 expires. The
idle state of the signal is low, so this can be used
only if CPOL is cleared to ‘0’.
D T0_Out toggle. SCK toggles whenever Timer 0
expires.
D T1_Out signal can be used as a clock. A pulse is
generated whenever Timer 1 expires. The idle state
of the signal is low, so this can be used only if CPOL
is cleared to ‘0’.
D T1_Out toggle. SCK toggles whenever Timer 1
expires.
SPI /I2C
Data Write
SPICON
I2CCON
I2C
Stretch
Control
Counter
Start/Stop
Detect
SPI /I2C
Data Read
Pad Control
DOUT
P1.2
P1.4
P3.6
P1.3
Logic
DOUT
TX_CLK
RX_CLK
SS
SCK/SCL
CNT_CLK
CNT INT
I2C INT
DIN
CLKS (refer to PASEL, SFR F2h)
SS
SCK
DIN
Figure 17. SPI/I2C Block Diagram
相关PDF资料
PDF描述
MPC8541PXAKF 32-BIT, 600 MHz, RISC PROCESSOR, PBGA783
MPC8541VTAKD 32-BIT, 600 MHz, RISC PROCESSOR, PBGA783
M30842MCT-XXXGP 32-BIT, MROM, 32 MHz, MICROCONTROLLER, PQFP144
MPC8347EZUADF 32-BIT, 266 MHz, RISC PROCESSOR, PBGA672
MPC8247CVRTMFX 32-BIT, 400 MHz, RISC PROCESSOR, PBGA516
相关代理商/技术参数
参数描述
MSC1201Y3RHHT 功能描述:模数转换器 - ADC Precision ADC & DAC w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MSC1201Y3RHHTG4 功能描述:模数转换器 - ADC 8051 CPU w/8kB Mem 24B ADC Current DAC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
MSC1202 制造商:BB 制造商全称:BB 功能描述:Precision, Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with 8051 Microcontroller and Flash Memory
MSC1202EVM 功能描述:数据转换 IC 开发工具 MSC1202EVM Eval Mod RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
MSC1202Y2 制造商:BB 制造商全称:BB 功能描述:Precision, Analog-to-Digital Converter (ADC) and Digital-to-Analog Converter (DAC) with 8051 Microcontroller and Flash Memory