- 您现在的位置：买卖IC网 > PDF目录19355 > MSC7116VF1000 (Freescale Semiconductor)DSP 16BIT W/DDR CTRLR 400-MAPBGA PDF资料下载
参数资料
| 型号： | MSC7116VF1000 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 43/60页 |
| 文件大小： | 0K |
| 描述： | DSP 16BIT W/DDR CTRLR 400-MAPBGA |
| 标准包装： | 90 |
| 系列： | StarCore |
| 类型： | 定点 |
| 接口： | 主机接口，I²C，UART |
| 时钟速率： | 266MHz |
| 非易失内存： | ROM（8 kB） |
| 芯片上RAM： | 400kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.20V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 400-LFBGA |
| 供应商设备封装： | 400-MAPBGA（17x17） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页当前第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
MSC7116 Data Sheet, Rev. 13
Hardware Design Considerations
Freescale Semiconductor
48
3.2.3
Power Planes
Each power supply pin (VDDC, VDDM, and VDDIO) should have a low-impedance path to the board power supply. Each GND pin
should be provided with a low-impedance path to ground. The power supply pins drive distinct groups of logic on the device.
The MSC7116 VDDC power supply pins should be bypassed to ground using decoupling capacitors. The capacitor leads and
associated printed circuit traces connecting to device power pins and GND should be kept to less than half an inch per capacitor
lead. A minimum four-layer board that employs two inner layers as power and GND planes is recommended. See Section 3.5
for DDR Controller power guidelines.
3.2.4
Decoupling
Both the I/O voltage and core voltage should be decoupled for switching noise. For I/O decoupling, use standard capacitor
values of 0.01
μF for every two to three voltage pins. For core voltage decoupling, use two levels of decoupling. The first level
should consist of a 0.01 F high frequency capacitor with low effective series resistance (ESR) and effective series inductance
(ESL) for every two to three voltage pins. The second decoupling level should consist of two bulk/tantalum decoupling
capacitors, one 10
μF and one 47 μF, (with low ESR and ESL) mounted as closely as possible to the MSC7116 voltage pins.
Additionally, the maximum drop between the power supply and the DSP device should be 15 mV at 1 A.
3.2.5
PLL Power Supply Filtering
The MSC7116 VDDPLL power signal provides power to the clock generation PLL. To ensure stability of the internal clock, the
power supplied to this pin should be filtered with capacitors that have low and high frequency filtering characteristics. VDDPLL
can be connected to VDDC through a 2 Ω resistor. VSSPLL can be tied directly to the GND plane. A circuit similar to the one
shown in Figure 35 is recommended. The PLL loop filter should be placed as closely as possible to the VDDPLL pin (which are
located on the outside edge of the silicon package) to minimize noise coupled from nearby circuits.The 0.01 F capacitor should
be closest to VDDPLL, followed by the 0.1 F capacitor, the 10 F capacitor, and finally the 2-Ω resistor to VDDC. These traces
should be kept short.
3.2.6
Power Consumption
You can reduce power consumption in your design by controlling the power consumption of the following regions of the device:
Extended core. Use the SC1400 Stop and Wait modes by issuing a stop or wait instruction.
Clock synthesis module. Disable the PLL, timer, watchdog, or DDR clocks or disable the CLKO pin.
AHB subsystem. Freeze or shut down the AHB subsystem using the GPSCTL[XBR_HRQ] bit.
Peripheral subsystem. Halt the individual on-device peripherals such as the DDR memory controller, Ethernet MAC,
HDI16, TDM, UART, I2C, and timer modules.
For details, see the “Clocks and Power Management” chapter of the MSC711x Reference Manual.
Figure 35. PLL Power Supply Filter Circuits
VDDC
VDDPLL
2
Ω
0.1 F 0.01 F
10 F
相关PDF资料 |
PDF描述 |
|---|---|
| HWS600-15 | PWR SUP IND 15V 43A SNG OUTPUT |
| DSP56321VF240 | IC DSP 24BIT 240MHZ 196-BGA |
| ATFC-0402-1N8-BT | INDUCTOR THIN FILM 1.8NH 0402 |
| VJ1206Y221KBBAT4X | CAP CER 220PF 100V 10% X7R 1206 |
| GBA06DTMD | CONN EDGECARD 12POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSC7116VM1000 | 功能描述:数字信号处理器和控制器 - DSP, DSC 7116 STARLITE - PBF RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MSC7116VM800 | 功能描述:IC DSP PROCESSOR 16BIT 400MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| MSC7118 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Low-Cost 16-bit DSP with DDR Controller |
| MSC7118VF1200 | 功能描述:DSP 16BIT W/DDR CTRLR 400-MAPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| MSC7118VM1200 | 功能描述:DSP 16BIT W/DDR CTRLR 400-MAPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。