参数资料
型号: MSP430F248TRGC
厂商: TEXAS INSTRUMENTS INC
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, QCC64
封装: PLASTIC, QFN-64
文件页数: 15/91页
文件大小: 1246K
代理商: MSP430F248TRGC
MSP430F23x
MSP430F24x(1)
MSP430F2410
SLAS547H
– JUNE 2007 – REVISED AUGUST 2011
Digital I/O
There are up to six 8-bit I/O ports implemented
—ports P1 through P6:
All individual I/O bits are independently programmable.
Any combination of input, output, and interrupt condition is possible.
Edge-selectable interrupt input capability for all eight bits of port P1 and P2.
Read/write access to port-control registers is supported by all instructions.
Each I/O has an individually programmable pullup/pulldown resistor.
Watchdog Timer (WDT+)
The primary function of the WDT+ module is to perform a controlled system restart after a software problem
occurs. If the selected time interval expires, a system reset is generated. If the watchdog function is not needed
in an application, the module can be disabled or configured as an interval timer and can generate interrupts at
selected time intervals.
Hardware Multiplier
The multiplication operation is supported by a dedicated peripheral module. The module performs 16x16, 16x8,
8x16, and 8x8 bit operations. The module is capable of supporting signed and unsigned multiplication as well as
signed and unsigned multiply and accumulate operations. The result of an operation can be accessed
immediately after the operands have been loaded into the peripheral registers. No additional clock cycles are
required.
Timer_A3
Timer_A3 is a 16-bit timer/counter with three capture/compare registers. Timer_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Table 16. Timer_A3 Signal Connections
DEVICE INPUT
MODULE INPUT
MODULE OUTPUT
OUTPUT PIN
INPUT PIN NUMBER
MODULE BLOCK
SIGNAL
NAME
SIGNAL
NUMBER
12 - P1.0
TACLK
ACLK
Timer
NA
SMCLK
21 - P2.1
TAINCLK
INCLK
13 - P1.1
TA0
CCI0A
13 - P1.1
22 - P2.2
TA0
CCI0B
17 - P1.5
CCR0
TA0
DVSS
GND
27 - P2.7
DVCC
VCC
14 - P1.2
TA1
CCI1A
14 - P1.2
CAOUT (internal)
CCI1B
18 - P1.6
CCR1
TA1
DVSS
GND
23 - P2.3
DVCC
VCC
ADC12(1) (internal)
15 - P1.3
TA2
CCI2A
15 - P1.3
ACLK (internal)
CCI2B
19 - P1.7
CCR2
TA2
DVSS
GND
24 - P2.4
DVCC
VCC
(1)
Not available in the MSP430F24x1 devices.
22
Copyright
2007–2011, Texas Instruments Incorporated
相关PDF资料
PDF描述
MB95F104ANSPMC 16-BIT, FLASH, 16.25 MHz, RISC MICROCONTROLLER, PQFP64
MPC8544EAVTARJ 32-BIT, 533 MHz, MICROPROCESSOR, PBGA783
MB89PV630-101C 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, CDIP64
MC9S12XF384J0CLM MICROCONTROLLER, PQFP112
MPC5561MVZ80R MICROCONTROLLER, PBGA324
相关代理商/技术参数
参数描述
MSP430F248TRGCR 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F248TRGCT 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2491TPM 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2491TPMR 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2491TRGCR 功能描述:16位微控制器 - MCU 16B Ultra-Lo-Pwr MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT