- 您现在的位置：买卖IC网 > PDF目录45324 > MT80C31-30R (ATMEL CORP) 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | MT80C31-30R |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | 1 MM HEIGHT, QFP-44 |
| 文件页数： | 130/170页 |
| 文件大小： | 4133K |
| 代理商： | MT80C31-30R |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页当前第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页
62
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
PWM). For non-PWM modes the COM0x1:0 bits control whether the output should be set, cleared or toggle at a
compare match (“Compare Match Output Unit” on page 60)
For detailed timing information refer to “Timer/Counter Timing Diagrams” on page 69.
11.8.1
Normal Mode
The simplest mode of operation is the Normal mode (WGM03:0 = 0). In this mode the counting direction is always
up (incrementing), and no counter clear is performed. The counter simply overruns when it passes its maximum
16-bit value (MAX = 0xFFFF) and then restarts from the BOTTOM (0x0000). In normal operation the Timer/Coun-
ter Overflow Flag (TOV0) will be set in the same timer clock cycle as the TCNT0 becomes zero. The TOV0 flag in
this case behaves like a 17th bit, except that it is only set, not cleared. However, combined with the timer overflow
interrupt that automatically clears the TOV0 flag, the timer resolution can be increased by software. There are no
special cases to consider in the Normal mode, a new counter value can be written anytime.
The Input Capture unit is easy to use in Normal mode. However, observe that the maximum interval between the
external events must not exceed the resolution of the counter. If the interval between events are too long, the timer
overflow interrupt or the prescaler must be used to extend the resolution for the capture unit.
The Output Compare units can be used to generate interrupts at some given time. Using the Output Compare to
generate waveforms in Normal mode is not recommended, since this will occupy too much of the CPU time.
11.8.2
Clear Timer on Compare Match (CTC) Mode
In Clear Timer on Compare or CTC mode (WGM03:0 = 4 or 12), the OCR0A or ICR0 Register are used to manipu-
late the counter resolution. In CTC mode the counter is cleared to zero when the counter value (TCNT0) matches
either the OCR0A (WGM03:0 = 4) or the ICR0 (WGM03:0 = 12). The OCR0A or ICR0 define the top value for the
counter, hence also its resolution. This mode allows greater control of the compare match output frequency. It also
simplifies the operation of counting external events.
The timing diagram for the CTC mode is shown in Figure 11-8 on page 62. The counter value (TCNT0) increases
until a compare match occurs with either OCR0A or ICR0, and then counter (TCNT0) is cleared.
Figure 11-8.
CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by either using the OCF0A or
ICF0 flag according to the register used to define the TOP value. If the interrupt is enabled, the interrupt handler
routine can be used for updating the TOP value. However, changing the TOP to a value close to BOTTOM when
the counter is running with none or a low prescaler value must be done with care since the CTC mode does not
have the double buffering feature. If the new value written to OCR0A or ICR0 is lower than the current value of
TCNT0, the counter will miss the compare match. The counter will then have to count to its maximum value
(0xFFFF) and wrap around starting at 0x0000 before the compare match can occur. In many cases this feature is
TCNTn
OCnA
(Toggle)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
1
4
Period
2
3
(COMnA1:0 = 1)
相关PDF资料 |
PDF描述 |
|---|---|
| MV80C31-36D | 8-BIT, 36 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51T-30R | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
| MV80C31-30R | 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44 |
| MS80C51C-16R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC44 |
| MF280C31-30R | 8-BIT, 30 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MT80C31BH | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述: |
| MT80C51BH | 制造商:ROCHESTER 制造商全称:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MT80C51FB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MT80C51FB/B | 制造商:Intel 功能描述: |
| MT80GB | 制造商:Datak Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。