参数资料
型号: MT80C51T-36D
厂商: TEMIC SEMICONDUCTORS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44
文件页数: 122/189页
文件大小: 4133K
代理商: MT80C51T-36D
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页当前第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页
55
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
11.3.2
External Clock Source
An external clock source applied to the T0 pin can be used as Timer/Counter clock (clk
Tn). The Tn pin is sampled
once every system clock cycle by the pin synchronization logic. The synchronized (sampled) signal is then passed
through the edge detector. Figure 11-3 on page 55 shows a functional equivalent block diagram of the T0 synchro-
nization and edge detector logic. The registers are clocked at the positive edge of the internal system clock (clk
I/O).
The latch is transparent in the high period of the internal system clock.
The edge detector generates one clk
T0 pulse for each positive (CS2:0 = 7) or negative (CS2:0 = 6) edge it detects.
Figure 11-3.
T0 Pin Sampling
The synchronization and edge detector logic introduces a delay of 2.5 to 3.5 system clock cycles from an edge has
been applied to the T0 pin to the counter is updated.
Enabling and disabling of the clock input must be done when T0 has been stable for at least one system clock
cycle, otherwise it is a risk that a false Timer/Counter clock pulse is generated.
Each half period of the external clock applied must be longer than one system clock cycle to ensure correct sam-
pling. The external clock must be guaranteed to have less than half the system clock frequency (f
ExtClk < fclk_I/O/2)
given a 50/50% duty cycle. Since the edge detector uses sampling, the maximum frequency of an external clock it
can detect is half the sampling frequency (Nyquist sampling theorem). However, due to variation of the system
clock frequency and duty cycle caused by oscillator source (crystal, resonator, and capacitors) tolerances, it is rec-
ommended that maximum frequency of an external clock source is less than f
clk_I/O/2.5.
An external clock source can not be prescaled.
11.4
Counter Unit
The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional counter unit. Figure 11-4 on
page 55 shows a block diagram of the counter and its surroundings.
Figure 11-4.
Counter Unit Block Diagram
Signal description (internal signals):
Tn_sync
(To Clock
Select Logic)
Edge Detector
Synchronization
DQ
LE
DQ
Tn
clk
I/O
TEMP (8-bit)
DATA BUS (8-bit)
TCNTn (16-bit Counter)
TCNTnH (8-bit)
TCNTnL (8-bit)
Control Logic
Count
Clear
Direction
TOVn
(Int.Req.)
Clock Select
TOP
BOTTOM
Tn
Edge
Detector
( From Prescaler )
clk
Tn
相关PDF资料
PDF描述
MS80C31-12R 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44
MT80C51C-12D 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44
MS80C31-20R 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44
MV80C51T-16D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MP80C31-30D 8-BIT, 30 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
MT80GB 制造商:Datak Corporation 功能描述:
MT80JSF1G72NDY-1G1F1A2 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.5V REGISTERED - Trays
MT80KSF1G72NDY-1G4F1A3 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.35V FULLY BUFFERED - Trays
MT810 制造商:MARKTECH 制造商全称:Marktech Corporate 功能描述:STANDARD T-1 3/4 LED LAMPS
MT-8100 制造商:Eclipse Tools 功能描述: