- 您现在的位置：买卖IC网 > PDF目录45322 > MT80C51T-36D (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | MT80C51T-36D |
| 厂商： | TEMIC SEMICONDUCTORS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, PQFP44 |
| 文件页数： | 157/189页 |
| 文件大小： | 4133K |
| 代理商： | MT80C51T-36D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页当前第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页
87
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
13.6
Changing Channel
The MUXn bits in the ADMUX Register are single buffered through a temporary register to which the CPU has ran-
dom access. This ensures that the channel selection only takes place at a safe point during the conversion. The
channel is continuously updated until a conversion is started. Once the conversion starts, the channel selection is
locked to ensure a sufficient sampling time for the ADC. Continuous updating resumes in the last ADC clock cycle
before the conversion completes (ADIF in ADCSRA is set). Note that the conversion starts on the following rising
ADC clock edge after ADSC is written. The user is thus advised not to write new channel selection values to
ADMUX until one ADC clock cycle after ADSC is written.
If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special care must be taken
when updating the ADMUX Register, in order to control which conversion will be affected by the new settings.
If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the ADMUX Register is
changed in this period, the user cannot tell if the next conversion is based on the old or the new settings. ADMUX
can be safely updated in the following ways:
When ADATE or ADEN is cleared.
During conversion, minimum one ADC clock cycle after the trigger event.
After a conversion, before the Interrupt Flag used as trigger source is cleared.
When updating ADMUX in one of these conditions, the new settings will affect the next ADC conversion.
13.6.1
ADC Input Channels
When changing channel selections, the user should observe the following guidelines to ensure that the correct
channel is selected:
In Single Conversion mode, always select the channel before starting the conversion. The channel selection
may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for
the conversion to complete before changing the channel selection.
In Free Running mode, always select the channel before starting the first conversion. The channel selection
may be changed one ADC clock cycle after writing one to ADSC. However, the simplest method is to wait for
the first conversion to complete, and then change the channel selection. Since the next conversion has already
started automatically, the next result will reflect the previous channel selection. Subsequent conversions will
reflect the new channel selection.
13.6.2
ADC Voltage Reference
The reference voltage of the ADC determines the conversion range, which in this case is limited to 0V (V
GND) and
V
REF = Vcc. Channels that exceed VREF will result in codes saturated at 0xFF.
13.7
ADC Noise Canceler
The ADC features a noise canceler that enables conversion during sleep mode to reduce noise induced from the
CPU core and other I/O peripherals. The noise canceler can be used with ADC Noise Reduction and Idle mode. To
make use of this feature, the following procedure should be used:
Make sure that the ADC is enabled and is not busy converting. Single Conversion mode must be selected and
the ADC conversion complete interrupt must be enabled.
Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a conversion once the CPU has been
halted.
If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake up the CPU and
execute the ADC Conversion Complete interrupt routine. If another interrupt wakes up the CPU before the ADC
conversion is complete, that interrupt will be executed, and an ADC Conversion Complete interrupt request will
相关PDF资料 |
PDF描述 |
|---|---|
| MS80C31-12R | 8-BIT, 12 MHz, MICROCONTROLLER, PQCC44 |
| MT80C51C-12D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP44 |
| MS80C31-20R | 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44 |
| MV80C51T-16D | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MP80C31-30D | 8-BIT, 30 MHz, MICROCONTROLLER, PDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MT80GB | 制造商:Datak Corporation 功能描述: |
| MT80JSF1G72NDY-1G1F1A2 | 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.5V REGISTERED - Trays |
| MT80KSF1G72NDY-1G4F1A3 | 制造商:Micron Technology Inc 功能描述:8GB 1GX72 DDR3 SDRAM MODULE PBF DIMM 1.35V FULLY BUFFERED - Trays |
| MT810 | 制造商:MARKTECH 制造商全称:Marktech Corporate 功能描述:STANDARD T-1 3/4 LED LAMPS |
| MT-8100 | 制造商:Eclipse Tools 功能描述: |
发布紧急采购，3分钟左右您将得到回复。