- 您现在的位置：买卖IC网 > PDF目录378679 > MTB2N60E (MOTOROLA INC) TMOS POWER FET 2.0 AMPERES 600 VOLTS PDF资料下载
参数资料
| 型号： | MTB2N60E |
| 厂商： | MOTOROLA INC |
| 元件分类： | JFETs |
| 英文描述： | TMOS POWER FET 2.0 AMPERES 600 VOLTS |
| 中文描述： | 2 A, 600 V, 3.8 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 文件页数： | 9/10页 |
| 文件大小： | 271K |
| 代理商： | MTB2N60E |
9
Motorola TMOS Power MOSFET Transistor Device Data
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a figure
for belt speed. Taken together, these control settings make up
a heating “profile” for that particular circuit board. On
machines controlled by a computer, the computer remembers
these profiles from one operating session to the next. Figure
18 shows a typical heating profile for use when soldering a
surface mount device to a printed circuit board. This profile will
vary among soldering systems but it is a good starting point.
Factors that can affect the profile include the type of soldering
system in use, density and types of components on the board,
type of solder used, and the type of board or substrate material
being used. This profile shows temperature versus time. The
line on the graph shows the actual temperature that might be
experienced on the surface of a test board at or near a central
solder joint. The two profiles are based on a high density and
a low density board. The Vitronics SMD310 convection/in-
frared reflow soldering system was used to generate this
profile. The type of solder used was 62/36/2 Tin Lead Silver
with a melting point between 177–189
°
C. When this type of
furnace is used for solder reflow work, the circuit boards and
solder joints tend to heat first. The components on the board
are then heated by conduction. The circuit board, because it
has a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may be
up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
170
°
C
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
Figure 18.
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
Typical Solder Heating Profile
相关PDF资料 |
PDF描述 |
|---|---|
| MTB2P50E | TMOS POWER FET 2.0 AMPERES 500 VOLTS |
| MTB30N06VL | TMOS POWER FET 30 AMPERES 60 VOLTS |
| MTB30P06V | TMOS POWER FET 30 AMPERES 60 VOLTS |
| MTB30P06 | TMOS POWER FET 30 AMPERES 60 VOLTS |
| MTB33N10E | TMOS POWER FET 33 AMPERES 100 VOLTS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTB2P50E | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TMOS POWER FET 2.0 AMPERES 500 VOLTS |
| MTB2P50ET4 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power MOSFET 2 Amps, 500 Volts P−Channel D2PAK |
| MTB2P50ET4G | 功能描述:MOSFET PFET 500V 2A 6O RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
| MTB306D | 功能描述:拨动开关 3PDT TOGGLE SWITCH Long Bat Actuator RoHS:否 制造商:C&K Components 触点形式:DPDT 开关功能:ON - ON - ON 电流额定值: 电压额定值 AC:20 V 电压额定值 DC:20 V 功率额定值:0.4 VA 端接类型:V-Bracket 安装风格: 端子密封:Epoxy 触点电镀:Gold 照明:Not Illuminated |
| MTB306D04 | 制造商:TE Connectivity 功能描述:Switch Toggle ON None ON 3PDT Bat Toggle Wire Lug 6A 250VAC 28VDC Panel Mount with Threads |
发布紧急采购，3分钟左右您将得到回复。