- 您现在的位置：买卖IC网 > PDF目录378679 > MTB6N60E1 (MOTOROLA INC) TMOS POWER FET 6.0 AMPERES 600 VOLTS PDF资料下载
参数资料
| 型号： | MTB6N60E1 |
| 厂商： | MOTOROLA INC |
| 元件分类： | JFETs |
| 英文描述： | TMOS POWER FET 6.0 AMPERES 600 VOLTS |
| 中文描述： | 6 A, 600 V, 1.2 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 文件页数： | 8/10页 |
| 文件大小： | 192K |
| 代理商： | MTB6N60E1 |
8
Motorola TMOS Power MOSFET Transistor Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. Solder
stencils are used to screen the optimum amount. These
stencils are typically 0.008 inches thick and may be made of
brass or stainless steel. For packages such as the SC–59,
SC–70/SOT–323, SOD–123, SOT–23, SOT–143, SOT–223,
SO–8, SO–14, SO–16, and SMB/SMC diode packages, the
stencil opening should be the same as the pad size or a 1:1
registration. This is not the case with the DPAK and D2PAK
packages. If one uses a 1:1 opening to screen solder onto the
drain pad, misalignment and/or “tombstoning” may occur due
to an excess of solder. For these two packages, the opening
in the stencil for the paste should be approximately 50% of the
tab area. The opening for the leads is still a 1:1 registration.
Figure 17 shows a typical stencil for the DPAK and D2PAK
packages. The pattern of the opening in the stencil for the
drain pad is not critical as long as it allows approximately 50%
of the pad to be covered with paste.
Figure 17. Typical Stencil for DPAK and
D2PAK Packages
SOLDER PASTE
OPENINGS
STENCIL
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
* Due to shadowing and the inability to set the wave height to
incorporate other surface mount components, the D2PAK is
not recommended for wave soldering.
相关PDF资料 |
PDF描述 |
|---|---|
| MTC311 | PC-ATA Solid State Disk Card(微机异步通信终端适配器的固态磁盘卡) |
| MTD10N05E | TMOS4 POWER FIELD EFFECT TRANSISTOR |
| MTD3302 | SINGLE TMOS POWER MOSFET 30 VOLTS RDS(on) = 10 mohm |
| MTDF1C02HD | COMPLEMENTARY DUAL TMOS POWER FET |
| MTE125N20E | TMOS POWER FET 125 AMPERES 200 VOLTS RDS(on) = 0.015 OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTB6N60ET4 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述: |
| MTB75N03HDL | 制造商:Motorola Inc 功能描述:MOSFET Transistor, N-Channel, TO-263AB |
| MTB75N05HD | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TMOS POWER FET 75 AMPERES 50 VOLTS |
| MTB75N05HDT4 | 功能描述:MOSFET N-CH 50V 75A D2PAK-3 RoHS:否 类别:分离式半导体产品 >> FET - 单 系列:- 标准包装:1,000 系列:MESH OVERLAY™ FET 型:MOSFET N 通道，金属氧化物 FET 特点:逻辑电平门 漏极至源极电压(Vdss):200V 电流 - 连续漏极(Id) @ 25° C:18A 开态Rds（最大）@ Id, Vgs @ 25° C:180 毫欧 @ 9A，10V Id 时的 Vgs(th)（最大）:4V @ 250µA 闸电荷(Qg) @ Vgs:72nC @ 10V 输入电容 (Ciss) @ Vds:1560pF @ 25V 功率 - 最大:40W 安装类型:通孔 封装/外壳:TO-220-3 整包 供应商设备封装:TO-220FP 包装:管件 |
| MTB75N06 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TMOS POWER FET 75 AMPERES 60 VOLTS |
发布紧急采购，3分钟左右您将得到回复。