- 您现在的位置：买卖IC网 > PDF目录98048 > MTP29N15E (ON SEMICONDUCTOR) 29 A, 150 V, 0.07 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-220AB PDF资料下载
参数资料
| 型号： | MTP29N15E |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | JFETs |
| 英文描述： | 29 A, 150 V, 0.07 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-220AB |
| 封装： | CASE 221A-09, 3 PIN |
| 文件页数： | 11/12页 |
| 文件大小： | 115K |
| 代理商： | MTP29N15E |
MTP29N15E
http://onsemi.com
8
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 16 shows a typical heating
profile for use when soldering a surface mount device to a
printed circuit board. This profile will vary among
soldering systems, but it is a good starting point. Factors
that can affect the profile include the type of soldering
system in use, density and types of components on the
board, type of solder used, and the type of board or
substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density
board. The Vitronics SMD310 convection/infrared reflow
soldering system was used to generate this profile. The type
of solder used was 62/36/2 Tin Lead Silver with a melting
point between 177–189
°C. When this type of furnace is
used for solder reflow work, the circuit boards and solder
joints tend to heat first. The components on the board are
then heated by conduction. The circuit board, because it has
a large surface area, absorbs the thermal energy more
efficiently, then distributes this energy to the components.
Because of this effect, the main body of a component may
be up to 30 degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°C
150
°C
100
°C
5
°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
° TO 219°C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
100
°C
150
°C
160
°C
170
°C
140
°C
Figure 16. Typical Solder Heating Profile
相关PDF资料 |
PDF描述 |
|---|---|
| MTSF1P02HDR2 | 1800 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MTSF1P02HDR2 | 1800 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MTSF2P02HDR2 | 3000 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MTSF2P02HDR2 | 2400 mA, 20 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MTSF2P03HDR2 | 2700 mA, 30 V, P-CHANNEL, Si, SMALL SIGNAL, MOSFET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MTP2H-E10-C | 功能描述:电缆束带 Mutiple Tie Plate, 2 Bundle, M-H Ties, # RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度: |
| MTP2H-E10-C39 | 功能描述:电缆束带 Mutiple Tie Plate, 2 Bundle, M-H Ties, # RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度: |
| MTP2H-E6-C | 功能描述:电缆束带 Mutiple Tie Plate, 2 Bundle, M-H Ties, # RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度: |
| MTP2N20 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:POWER FIELD EFFECT TRANSISTOR, N-CHANNEL ENHANCEMENT-MODE SILICON GATE |
| MTP2N35 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:N-Channel Power MOSFETs, 2.25A, 350-400V |
发布紧急采购，3分钟左右您将得到回复。