参数资料
| 型号： | NCP1571DG |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 8-SOIC |
| 产品变化通告： | Product Obsolescence 05/Oct/2010 |
| 标准包装： | 98 |
| PWM 型： | 电流/电压模式，V²? |
| 输出数： | 1 |
| 频率 - 最大： | 250kHz |
| 电源电压： | 11.4 V ~ 12.6 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
NCP1571
APPLICATION INFORMATION
THEORY OF OPERATION
The NCP1571 is a simple, synchronous, fixed?frequency,
low?voltage buck controller using the V 2 control method. It
provides a programmable?delay Power Good function to
indicate when the output voltage is out of regulation.
V 2 Control Method
The V 2 control method uses a ramp signal generated by
the ESR of the output capacitors. This ramp is proportional
to the AC current through the main inductor and is offset by
the DC output voltage. This control scheme inherently
compensates for variation in either line or load conditions,
since the ramp signal is generated from the output voltage
itself. The V 2 method differs from traditional techniques
such as voltage mode control, which generates an artificial
ramp, and current mode control, which generates a ramp
using the inductor current.
time to the output load step is not related to the crossover
frequency of the error signal loop.
The error signal loop can have a low crossover frequency,
since the transient response is handled by the ramp signal
loop. The main purpose of this ‘slow’ feedback loop is to
provide DC accuracy. Noise immunity is significantly
improved, since the error amplifier bandwidth can be rolled
off at a low frequency. Enhanced noise immunity improves
remote sensing of the output voltage, since the noise
associated with long feedback traces can be effectively
filtered.
Line and load regulation are drastically improved because
there are two independent control loops. A voltage mode
controller relies on the change in the error signal to
compensate for a deviation in either line or load voltage.
This change in the error signal causes the output voltage to
change corresponding to the gain of the error amplifier,
which is normally specified as line and load regulation. A
current mode controller maintains a fixed error signal during
RAMP
?
PWM
+
GATE(H)
GATE(L)
Output
Voltage
line transients, since the slope of the ramp signal changes in
this case. However, regulation of load transients still requires
a change in the error signal. The V 2 method of control
maintains a fixed error signal for both line and load variation,
since the ramp signal is affected by both line and load.
The stringent load transient requirements of modern
microprocessors require the output capacitors to have very
Slope
Compensation
Error
Amplifier
V FB
low ESR. The resulting shallow slope in the output ripple can
lead to pulse width jitter and variation caused by both random
COMP
Error
Signal
?
+
Reference
Voltage
and synchronous noise. A ramp waveform generated in the
oscillator is added to the ramp signal from the output voltage
to provide the proper voltage ramp at the beginning of each
switching cycle. This slope compensation increases the noise
Figure 21. V 2 Control with Slope Compensation
The V 2 control method is illustrated in Figure 21. The
output voltage generates both the error signal and the ramp
signal. Since the ramp signal is simply the output voltage, it
is affected by any change in the output, regardless of the
origin of that change. The ramp signal also contains the DC
portion of the output voltage, allowing the control circuit to
drive the main switch from 0% to 100% duty cycle as
required.
A variation in line voltage changes the current ramp in the
inductor, which causes the V 2 control scheme to compensate
the duty cycle. Since any variation in inductor current
modifies the ramp signal, as in current mode control, the V 2
control scheme offers the same advantages in line transient
response.
A variation in load current will affect the output voltage,
modifying the ramp signal. A load step immediately changes
the state of the comparator output, which controls the main
switch. The comparator response time and the transition
speed of the main switch determine the load transient
response. Unlike traditional control methods, the reaction
immunity, particularly at duty cycles above 50%.
Startup
The NCP1571 features a programmable Soft?Start
function, which is implemented through the error amplifier
and the external compensation capacitor. This feature
prevents stress to the power components and limits output
voltage overshoot during startup. As power is applied to the
regulator, the NCP1571 undervoltage lockout circuit (UVL)
monitors the IC’s supply voltage (V CC ). The UVL circuit
holds both gate outputs low until V CC exceeds the 8.5 V
threshold. A hysteresis function of 1.0 V improves noise
immunity. The compensation capacitor connected to the
COMP pin is charged by a 30 m A current source. When the
capacitor voltage exceeds the 0.525 V offset of the PWM
comparator, the PWM control loop will allow switching to
occur. The upper gate driver GATE(H) is activated, turning
on the upper MOSFET. The current ramps up through the
main inductor and linearly powers the output capacitors and
load. When the regulator output voltage exceeds the COMP
pin voltage minus the 0.525 V PWM comparator offset
threshold and the artificial ramp, the PWM comparator
terminates the initial pulse.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1573DR2 | IC REG CTRLR BUCK PWM 8-SOIC |
| NCP1575DR2G | IC REG CTRLR BUCK PWM 8-SOIC |
| NCP1579DR2G | IC REG CTRLR BUCK PWM VM 8-SOIC |
| NCP1580DR2G | IC REG CTRLR BUCK PWM VM 8-SOIC |
| NCP1581DR2G | IC REG CTRLR BUCK PWM VM 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1571DR2 | 功能描述:DC/DC 开关控制器 Low Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP1571DR2G | 功能描述:DC/DC 开关控制器 Low Voltage Synchronous Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP1573D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| NCP1573DR2 | 功能描述:IC REG CTRLR BUCK PWM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| NCP1575D | 功能描述:DC/DC 开关控制器 Low Voltage RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。