- 您现在的位置：买卖IC网 > PDF目录15054 > NCP5424DG (ON Semiconductor)IC REG CTRLR BUCK PWM 16-SOIC PDF资料下载
参数资料
| 型号： | NCP5424DG |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 16-SOIC |
| 产品变化通告： | Product Obsolescence 21/Jan/2010 |
| 标准包装： | 48 |
| PWM 型： | 电流/电压模式，V²? |
| 输出数： | 1 |
| 频率 - 最大： | 750kHz |
| 占空比： | 100% |
| 电源电压： | 10.8 V ~ 13.2 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
NCP5424
capacitor on the Comp1 pin and a 0.01 m F capacitor on the
Comp2 pin in suggested.
Selecting Current Sharing Current Limit
In a two?phase single output application, there are two
different current limit options. The Master (Controller One)
current limit can be set equal to the Slave (Controller Two)
which brings both controllers into Hiccup Mode during an
overcurrent condition. The second option is to set Slave
current limit lower than that of the Master, which limits the
Slave’s input power when its limit is reached, while the
output voltage remains in regulation. Both Master and Slave
will go into hiccup mode if the Master ’s limit is reached.
During Cycle?By?Cycle current limit, the Slave’s operating
frequency will decrease in half, due to pulse skipping,
resulting in phase overlap. This overlap will increase the
output voltage ripple.
Exceeding 70 mV between the IS+ and IS? pins trips the
current limits. A divided down V out signal is used to generate
the IS? reference, and inductor sensing of the controllers
output chokes provide the output current information to
IS+X pin. The inductor sensing is achieved by placing a
series RC in parallel with the output choke. With the RC time
constant selected to equal the L/R L time constant, the
voltage across the capacitor will be equal to the voltage drop
across the internal resistance of the inductor.
The resistance of the output choke (LSR) must be known
to calculate the overcurrent trip point. The voltage drop
across the inductor at overcurrent is calculated as follows:
where:
V out = Output regulated voltage.
V os = Offset voltage, example above was 20 mV.
R4 = Chosen value, 10 K W is a good choice.
If V os is larger than 70 mV, then the current signal from the
output chokes must be divided down. For example, if the
inductor ’s LSR is equal to 8.0 m W and the current limit is
15 A, then the current signal is 120 mV, which is almost
twice the comparator ’s offset (70 mV). This signal can be
divided down by adding a resistor (R1) in parallel with the
capacitor (C6) in the inductor sensing network, see Figure 1.
The divider R1 and R2 can be set to equal value to divide the
current signal in half and equation (3) should be used to
select the proper voltage divider. Notice that the divider R1
and R2, divides down the voltage applied to the capacitor
C RC by a factor of 2. This divides the voltage across the
output inductor ’s LSR by a factor of two and results in twice
the current limit. This scaling technique is another way the
current limit may be set so that virtually any current limit
may be obtained.
To ensure accuracy, the equivalent parallel resistance of
R1 and R2 should be greater or equal to the value R RC , the
resistance value calculated from equation (2). If Hiccup
Mode is used, then both sensing network values must be
equal.
If Cycle?by?Cycle is desired, then equation (1), (2) and
(3) should be used to select the Slave’s inductor sensing
network for the desired current limit and equation (4) should
be used to raise the Master ’s current limit, Hiccup Mode,
VL + RL · Iout
(eq. 1)
above the Slave’s limit.
where:
V L = Voltage drop across the inductor,
R2 +
R1(1 * Ratio)
Ratio
(eq. 4)
Ratio + slave.limit , Master ’s and Slave’s current
R L = LSR of the inductor,
I out = Output current trip point for one phase.
For Hiccup Mode only, both sensing networks should have
the identical values.
If the inductor selected has a 5.0 m W LSR and the current
limit is 10 A through one of the phases, then the analog
signal will be 50 mV. Since this value is less than 70 mV,
then the IS? divider, R3 and R4 in Figure 1, must scale down
where:
R1 = Chosen value, 10 K W is recommended,
I
Imaster.limit
limit ratio.
To ensure greater accuracy, the equivalent parallel
resistance of R1 and R2 should be greater or equal to the
value R RC , value calculated from equation (2).
RRC v R1 · R2
the V out by 20 mV, thus placing a 20 mV offset across the IS?
and IS+x pin at no load and allowing the Controllers to trip
into current limit with only 50 mV across the inductor. In
R1 ) R2
(eq. 5)
RRC +
L
this case, the RC values are calculated using the following
equation:
(eq. 2)
CRC · RL
L= Inductor value, both Controllers should have the
same value.
R L = Internal resistance of L, see data sheet.
C RC = Chosen value, 0.1 m F will make R a reasonable
value.
And the IS? divider value can be selected with this equation.
Current Sensing
The current supplied to the load can be sensed easily using
the IS+ and IS? pins for the output. These pins sense a
voltage, proportional to the output current, and compare it to
a fixed internal voltage threshold. When the differential
voltage exceeds 70 mV, the internal overcurrent protection
system goes into hiccup mode. Two methods for sensing the
current are available.
Sense Resistor. A sense resistor can be added in series
with the inductor. When the voltage drop across the sense
resistor exceeds the internal voltage threshold of 70 mV, a
R3 +
Vout
Vout * Vos
* 1 · R4
(eq. 3)
fault condition is set.
The sense resistor is selected according to:
http://onsemi.com
15
相关PDF资料 |
PDF描述 |
|---|---|
| NCP5424D | IC REG CTRLR BUCK PWM 16-SOIC |
| NCP5211DR2G | IC REG CTRLR BUCK PWM 14-SOIC |
| GEM22DTBT-S273 | CONN EDGECARD 44POS R/A .156 SLD |
| GEM22DTAT-S273 | CONN EDGECARD 44POS R/A .156 SLD |
| GBA30DRMZ-S273 | CONN EDGECARD 60POS .125 SQ WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP5424DR2 | 功能描述:DC/DC 开关控制器 Dual Sync. Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5424DR2G | 功能描述:DC/DC 开关控制器 Dual Sync. Buck w/Current Sharing RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| NCP5424EVB | 功能描述:电源管理IC开发工具 ANA SW REG EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| NCP5425 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Dual Synchronous Buck Controller |
| NCP5425/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Dual Synchronous Buck Controller |
发布紧急采购，3分钟左右您将得到回复。