参数资料
| 型号： | NCV2002SN1T1 |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R 0.9V 1A 6-TSOP |
| 产品变化通告： | Product Obsolescence 11/Feb/2009 |
| 标准包装： | 3,000 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 1.3 V/µs |
| 增益带宽积： | 900kHz |
| 电流 - 输入偏压： | 10pA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 820µA |
| 电流 - 输出 / 通道： | 128mA |
| 电压 - 电源，单路/双路(±)： | 0.9 V ~ 7 V，±0.45 V ~ 3.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74，SOT-457 |
| 供应商设备封装： | 6-TSOP |
| 包装： | 带卷 (TR) |
NCS2002, NCV2002
http://onsemi.com
11
Output
The output stage consists of complementary P and N
channel devices connected to provide railtorail output
drive. With a 2.0 k load, the output can swing within 50 mV
of either rail. It is also capable of supplying over 75 mA
when powered from 5.0 V and 1.0 mA when powered from
0.9 V.
When connected as a unity gain follower, the NCS2002
can directly drive capacitive loads in excess of 820 pF at
room temperature without oscillating but with significantly
reduced phase margin. The unity gain follower
configuration exhibits the highest bandwidth and is most
prone to oscillations when driving a high value capacitive
load. The capacitive load in combination with the
amplifier’s output impedance, creates a phase lag that can
result in an underdamped pulse response or a continuous
oscillation. Figure 35 shows the effect of driving a large
capacitive load in a voltage follower type of setup. When
driving capacitive loads exceeding 820 pF, it is
recommended to place a low value isolation resistor
between the output of the op amp and the load, as shown in
Figure 34. The series resistor isolates the capacitive load
from the output and enhances the phase margin. Refer to
Figure 36. Larger values of R will result in a cleaner output
waveform but excessively large values will degrade the
large signal rise and fall time and reduce the output
amplitude. Depending upon the capacitor characteristics,
the isolation resistor value will typically be between 50 to
500
W. The output drive capability for resistive and
Figure 34. Capacitance Load Isolation
+
-
Output
R
Isolation resistor R = 50 to 500
CL
Input
Note that the lowest phase margin is observed at cold
temperature and low supply voltage.
Enable Pin
The enable pin allows the user to externally control the
device. if the enable pin is pulled below the input disable
threshold voltage (VEN < 45% VCC), the amplifier is
disabled. Once the enable pin is taken above the threshold
voltage (VEN = 60% VCC), the amplifier will turn on. In the
event the enable pin is not connected, the amplifier will
remain on by default
相关PDF资料 |
PDF描述 |
|---|---|
| ESD02A5V5R25V | SUPPRESSOR ESD 0.2PF 5.5VDC 0402 |
| 0034.5042 | FUSE 800MA 250V 5X20 T-LAG GLASS |
| 0034.5039 | FUSE 400MA 250V 5X20 T-LAG GLASS |
| LT1636CDD | IC OPAMP R-R IN/OUT 220KHZ 8DFN |
| RT0603DRD072K49L | RES 2.49K OHM 1/10W .5% 0603 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV2002SN1T1G | 功能描述:运算放大器 - 运放 0.9-7V Sngl Rail to Rail Extended Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| NCV2002SN2T1 | 功能描述:运算放大器 - 运放 0.9-7V Sngl Rail to RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| NCV2002SN2T1G | 功能描述:运算放大器 - 运放 0.9-7V Sngl Rail to Rail Extended Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| NCV2200SN1T1G | 功能描述:IC COMPARATOR COMPL SOT-23-5 RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:通用 元件数:1 输出类型:CMOS，推挽式，满摆幅，TTL 电压 - 电源，单路/双路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 电压 - 输入偏移（最小值）:5mV @ 5.5V 电流 - 输入偏压（最小值）:1pA @ 5.5V 电流 - 输出（标准）:- 电流 - 静态（最大值）:24µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:450ns 磁滞:±3mV 工作温度:-40°C ~ 85°C 封装/外壳:6-WFBGA，CSPBGA 安装类型:表面贴装 包装:管件 其它名称:Q3554586 |
| NCV2200SN2T1G | 功能描述:校验器 IC ANA COMPARATORS RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。