- 您现在的位置：买卖IC网 > Datasheet目录346 > NCV8855BMNR2GEVB (ON Semiconductor)BOARD EVALUATION NCV8855 ASIC Datasheet资料下载
参数资料
| 型号： | NCV8855BMNR2GEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION NCV8855 ASIC |
| 设计资源： | NCV8855BMNR2GEVB Schematic NCV8855 BOM |
| 标准包装： | 1 |
| 主要目的： | DC/DC，LDO 步降 |
| 输出及类型： | 4，非隔离 |
| 电流 - 输出： | 2.5A |
| 输入电压： | 9 V ~ 18 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 170kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | NCV8855 |
| 其它名称： | NCV8855BMNR2GEVBOS |
NCV8855
PIN FUNCTION DESCRIPTIONS
Pin No.
5
6
7
8
22
35
36
4
37
Symbol
SYS_EN
LDO_EN
HS_EN
HOT_FLG
DRV_VPP
5V_IC
DRAIL
SYNC
AGND
Description
Main enable pin for the IC. A logic high on this pin will enable the part. Leaving this pin floating or driving it to
ground will place the IC in shutdown mode.
Enable pin for both LDO controllers. A logic high on this pin will enable both LDO controllers. If this pin is left
floating, an internal pull down keeps the LDOs disabled.
Enable pin for the high ? side load switch. A logic high on this pin will enable the HSS. If this pin is left floating,
an internal pull down keeps the HSS disabled.
Thermal warning indicator. This pin provides an early warning signal of an impending thermal shutdown.
Output of the internal 7.2 V linear regulator. Bypass this pin with 1 m F to ground.
Output of the internal 5 V linear regulator. Bypass this pin with 0.1 m F to ground.
Output of the internal 4.2 V linear regulator. Bypass this pin with 0.1 m F to ground.
Synchronization pin. Use this pin to synchronize the internal oscillator to an external clock. If synchronization
is not used, connect this pin to AGND.
Analog ground. Reference point for internal signals.
SWITCH ? MODE POWER SUPPLY 1 (SMPS1) PIN CONNECTIONS
27
29
30
25
24
23
21
20
OCSET
SW_FB1
COMP1
BST1
GH1
SN1
GL1
PGND
Overcurrent set pin, used to set the current limit threshold. A resistor connected from this pin and the upper
MOSFET Drain sets the current limit protection level.
Output voltage feedback pin. Connect a resistor divider network to VOUT1 to set the desired output voltage.
This pin is the output of the error amplifier and the non-inverting input of the PWM comparator. Use
this pin in conjunction with the SW_FB1 pin to compensate the voltage-mode control feedback
loop.
This pin is the supply rail for the upper N ? Channel MOSFET. An internal bootstrap diode brings DRV_VPP to
this pin. Connect a ceramic capacitor (C BST1 ) between this pin and the SN1 pin. A typical value for C BST1 is
0.1 m F.
GH1 is the output pin of the internal upper N ? Channel MOSFET gate driver. Keep the trace from this pin to
the gate of the upper MOSFET as short as possible to achieve the best turn ? on and turn ? off performance
and to reduce electro ? magnetic emissions.
This pin is the return path of the upper floating gate driver. Connect this pin to the source of the upper
MOSFET. This pin is also used to sense the current flowing through the upper MOSFETs.
GL1 is the output pin of the synchronous rectifier gate driver. Connect this pin to the lower N ? channel
MOSFET.
This pin is the return path for SMPS1 lower MOSFET driver current. Connect this pin to the source of the
lower MOSFET.
PINS NOT INTERNALLY CONNECTED TO SILICON
EP
12 thru
19
?
Exposed pad of QFN package. Connect to printed circuit board ground to improve thermal performance.
These pins can be left floating or tied to ground to improve thermal performance.
SWITCH ? MODE POWER SUPPLY 2 (SMPS2) PIN CONNECTIONS
10
3
2
11
9
VIN_SW
SW_FB2
COMP2
BST2
SN2
This pin is the supply rail for the internal upper N ? Channel MOSFET. Bypass this pin with a local ceramic
capacitor. Additional bulk capacitance may be required based off output requirements. Refer to application
section for more information.
Output voltage feedback pin. Connect a resistor divider network to VOUT2 to set the desired output voltage.
This pin is the output of the error amplifier and the non ? inverting input of the PWM comparator. Use this pin
in conjunction with the SW_FB2 pin to compensate the voltage ? controlled feedback loop.
This pin is the supply rail for the internal upper N ? Channel MOSFET. An internal bootstrap diode brings
DRV_VPP to this pin. Connect a ceramic capacitor (C BST2 ) between this pin and the SN2 pin. A typical value
for C BST2 is 0.1 m F.
Source output of the internal upper N ? channel MOSFET.
http://onsemi.com
3
相关PDF资料 |
PDF描述 |
|---|---|
| NCV8871BSTGEVB | BOARD EVAL NCV8871BST BOOST CTLR |
| NHC-14150 | VALULINE 8" X 8.5" X 1.75" |
| NHC-14151 | VALULINE 8" X 17" X 1.75" |
| NHC-14152 | VALULINE 13" X 17" X 1.75" |
| NHC-14153 | VALULINE 8" X 8.5" X 3.5" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV8870 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Automotive Grade Non-Synchronous Boost Controller |
| NCV887000 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Automotive Grade Non-Synchronous Boost Controller |
| NCV887000D1R2G | 功能描述:低压差稳压器 - LDO Auto Grade Non-Sync Boost Controller RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| NCV887001 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Automotive Grade Non-Synchronous Boost Controller |
| NCV887001D1R2G | 功能描述:低压差稳压器 - LDO Auto Grade Non-Sync Boost Controller RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。