- 您现在的位置：买卖IC网 > PDF目录98051 > PCA8802CX8/B/1 (NXP SEMICONDUCTORS) SPECIALTY ANALOG CIRCUIT, PBGA8 PDF资料下载
参数资料
| 型号： | PCA8802CX8/B/1 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| 封装： | 1.19 X 1.14 MM, 0.29 MM HEIGHT, LEAD FREE, WLCSP-8 |
| 文件页数： | 8/34页 |
| 文件大小： | 160K |
| 代理商： | PCA8802CX8/B/1 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
PCA8802_1
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 01 — 19 February 2009
16 of 34
NXP Semiconductors
PCA8802
Smartcard RTC
9.6.5 Instruction 32k_cmd
The 32.768 kHz enable instruction (32k_cmd) is intended to aid with oscillator
characterization during system development. With this instruction it is possible to obtain a
32.768 kHz clock on the INT pin which may be used for measurement.
This mode does not affect other operation of the chip with the exception of loss of interrupt
output.
9.6.6 Instruction fst_cmd
The fast mode instruction (fst_cmd) is intended to enable faster system development.
When enabled, the counter will increment once every second instead of once every 32
seconds. Interrupt pulses will also be generated once every second.
When using fst_cmd, data access to the device must be completed within 1 second, if not
then counter increments will be lost. The 1 second period is measured from the ACK cycle
of a valid slave address to the next STOP or repeated START. A repeated START will be
sufcient to allow the counter to increment.
9.6.7 Instruction set_cmd
The counter can be set to any value using the set instruction (set_cmd). Partial writing of
the data parameters will result in partial setting of the counter. E.g. if data transfer is
stopped after P1[23:16] is transmitted, then only bit 23 to bit 16 will be updated.
Table 7.
Power-down sequence
Step Action
Code sequence Note
To enter power-down
1
initiate transfer
START condition -
2
send wrt_cmd
1010 0000
-
3
enable dvs_cmd
0001 0001
stop the divider
4
set counter with set_cmd
1000 0000
set the counter = AAAAAAh
1010 1010
P1[23:16]
1010 1010
P2[15:8]
1010 1010
P3[7:0]
5
enable pwd_cmd
0010 0001
stop the oscillator
6
end transfer
STOP condition
-
7
device is now in a
power-down state
--
To exit power-down
1
initiate transfer
START condition -
2
send wrt_cmd
1010 0000
-
3
disable pwd_cmd
0010 0000
oscillator starts on the ACK cycle of this
instruction
4
disable dvs_cmd
0001 0000
enable the divider again
5
end transfer
STOP condition
-
相关PDF资料 |
PDF描述 |
|---|---|
| PCA8802U/2AA/1 | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| PCF1252-9TD-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| PCF1252-4TD-T | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| PCF50603HN | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC48 |
| PCF8591T-T | SPECIALTY ANALOG CIRCUIT, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA8802U | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:ultra low power oscillator with integrated counter for initiating one time password generation |
| PCA8802U/12AA/1,00 | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| PCA8802U/2AA/1,026 | 功能描述:实时时钟 ultra LOW POWER OSC Smartcard RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| PCA8802UG/12KB/1,0 | 制造商:NXP Semiconductors 功能描述:PCA8802UG/UNCASED/FOIL//12KB/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC SMARTCARD RTC ULP OSC 8WLCSP |
| PCA887A/CW/DP1S | 制造商:Rochester Electronics LLC 功能描述: 制造商:Zarlink Semiconductor Inc 功能描述: 制造商:ZARLINK 功能描述: |
发布紧急采购，3分钟左右您将得到回复。