参数资料
| 型号： | PCA9500PW,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 24/26页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 产品培训模块： | I²C Bus Fundamentals |
| 特色产品： | NXP - I2C Interface |
| 标准包装： | 96 |
| 接口： | I²C，SM 总线 |
| 输入/输出数： | 8 |
| 中断输出： | 无 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2.5 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 包括： | EEPROM，POR |
| 产品目录页面： | 824 (CN2011-ZH PDF) |
| 其它名称： | 568-1025-5 935271534112 PCA9500PW |
PCA9500_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 15 April 2009
7 of 26
NXP Semiconductors
PCA9500
8-bit I2C-bus and SMBus I/O port with 2-kbit EEPROM
7.3.1 Quasi-bidirectional I/Os
A quasi-bidirectional I/O can be used as an input or output without the use of a control
signal for data direction. At power-on the I/Os are HIGH. In this mode, only a current
source to VDD is active. An additional strong pull-up to VDD allows fast rising edges into
heavily loaded outputs. These devices turn on when an output is written HIGH, and are
switched off by the negative edge of SCL. The I/Os should be HIGH before being used as
inputs. See Figure 9.
7.4 Memory operations
7.4.1 Write operations
Write operations require an additional address eld to indicate the memory address
location to be written. The address eld is eight bits long, providing access to any one of
the 256 words of memory. There are two types of write operations, ‘byte write’ and
‘page write’.
Write operation is possible when the Write Control pin (WC) is put at a LOW logic level (0).
When this control signal is set at 1, write operation is not possible and data in the memory
is protected.
‘Byte write’ and ‘page write’ explained below assume that WC is set to 0.
7.4.1.1
Byte write
To perform a byte write the START condition is followed by the memory slave address and
the R/W bit set to 0. The PCA9500 will respond with an acknowledge and then consider
the next eight bits sent as the word address and the eight bits after the word address as
the data. The PCA9500 will issue an acknowledge after the receipt of both the word
address and the data. To terminate the data transfer the master issues the STOP
condition, initiating the internal write cycle to the non-volatile memory. Only write and read
operations to the quasi-bidirectional I/Os are allowed during the internal write cycle.
Fig 9.
Transient pull-up current (IOHt) while IO3 changes from LOW to HIGH and back to LOW
0
A
S
slave address (I/O expander)
START condition
R/W
acknowledge
from slave
002aae593
1
data to port
A
acknowledge
from slave
12345678
SCL
9
SDA
0
A
IO3 output voltage
IO3 pull-up output current
acknowledge
from slave
data to port
1
0
A2 A1 A0
0
IO3
P
STOP
condition
IO3
IOHt
IOH
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9554PW/Q900,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9555BS,118 | IC I/O EXPANDER I2C 16B 24HVQFN |
| PCA9507DP,118 | IC I/O EXPANDER I2C 24B 8TSSOP |
| PCA9670PW,112 | IC I/O EXPANDER I2C 8B 16TSSOP |
| PCA9574BS,118 | IC I/O EXPANDER I2C 8B 16HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9501 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit I2C and SMBus I/O port with interrupt, 2-kbit EEPROM and 6 address pins |
| PCA9501A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns |
| PCA9501BS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit I2C and SMBus I/O port with interrupt, 2-kbit EEPROM and 6 address pins |
| PCA9501BS,118 | 功能描述:接口-I/O扩展器 8BIT I2C FMQB GPIONT RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| PCA9501BS,118-CUT TAPE | 制造商:NXP 功能描述:8-bit 8 I/O I2C-bus Expander On Board 2 kb EEPROM Surface Mount - HVQFN-20 |
发布紧急采购，3分钟左右您将得到回复。