- 您现在的位置：买卖IC网 > Datasheet目录349 > PCA9530D,118 (NXP Semiconductors)IC LED DRIVER RGB 8-SOIC Datasheet资料下载
参数资料
| 型号： | PCA9530D,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER RGB 8-SOIC |
| 产品培训模块： | LED Controllers I²C Bus Fundamentals |
| 标准包装： | 1 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | RGB |
| 频率： | 400kHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 产品目录页面： | 825 (CN2011-ZH PDF) |
| 其它名称： | 568-1830-6 |
NXP Semiconductors
PCA9530
2-bit I 2 C-bus LED dimmer
6.3.5 PWM1 - Pulse Width Modulation 1
The PWM1 register determines the duty cycle of BLINK1. The outputs are LOW (LED on)
when the count is less than the value in PWM1 and HIGH (LED off) when it is greater.
If PWM1 is programmed with 00h, then the PWM1 output is always HIGH (LED off).
The duty cycle of BLINK1 = PWM1 / 256.
Table 8.
PWM1 - Pulse Width Modulation 1 register description
Bit
Symbol
Default
7
PWM1
[7]
1
6
PWM1
[6]
0
5
PWM1
[5]
0
4
PWM1
[4]
0
3
PWM1
[3]
0
2
PWM1
[2]
0
1
PWM1
[1]
0
0
PWM1
[0]
0
6.3.6 LS0 - LED selector
The LS0 LED select register determines the source of the LED data.
00 = output is set high-impedance (LED off; default)
01 = output is set LOW (LED on)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
Table 9. LS0 - LED selector register bit description
Legend: * default value.
Register
LS0
Bit
7:4
3:2
1:0
Value
1111*
00*
00*
Description
reserved
LED1 selected
LED0 selected
6.4 Pins used as GPIOs
LEDn pins not used to control LEDs can be used as General Purpose I/Os (GPIOs).
For use as input, set LEDn to high-impedance (00) and then read the pin state via the
INPUT register.
For use as output, connect external pull-up resistor to the pin and size it according to the
DC recommended operating characteristics. LEDn output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is programmed LOW through
the ‘LED selector’ register LS0. The output can be pulse-width controlled when PWM0 or
PWM1 are used.
6.5 Power-on reset
When power is applied to V DD , an internal Power-On Reset (POR) holds the PCA9530 in
a reset condition until V DD has reached V POR . At that point, the reset condition is released
and the PCA9530 registers are initialized to their default states, all the outputs in the
OFF state. Thereafter, V DD must be lowered below 0.2 V to reset the device.
PCA9530_3
? NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 26 February 2009
6 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| PCA9531PW,118 | IC LED DRIVER RGB 16-TSSOP |
| PCA9532D,118 | IC LED DRIVER RGB 24-SOIC |
| PCA9533DP/01,118 | IC LED DRIVER RGB 8-TSSOP |
| PCA9550DP,118 | IC LED DRIVER BLINKER 8-TSSOP |
| PCA9551BS,118 | IC LED DRIVER BLINKER 16-HVQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PCA9530DP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:2-bit I2C LED dimmer |
| PCA9530DP,118 | 功能描述:LED照明驱动器 I2C LED DIMMER 2BIT RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9530D-T | 功能描述:LED照明驱动器 2-BIT I2C FM OD LED DIM RST RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| PCA9531 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit I2C-bus LED dimmer |
| PCA9531BS | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit I2C LED dimmer |
发布紧急采购，3分钟左右您将得到回复。