参数资料
型号: PIC12F1822-E/MF
厂商: Microchip Technology
文件页数: 34/109页
文件大小: 0K
描述: MCU 8BIT 2K FLASH 8DFN
标准包装: 120
系列: PIC® XLP™ 12F
核心处理器: PIC
芯体尺寸: 8-位
速度: 32MHz
连通性: I²C,LIN,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 6
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 8-VDFN 裸露焊盘
包装: 管件
221
7674F–AVR–09/09
ATmega164P/324P/644P
19.7
Transmission Modes
The TWI can operate in one of four major modes. These are named Master Transmitter (MT),
Master Receiver (MR), Slave Transmitter (ST) and Slave Receiver (SR). Several of these
modes can be used in the same application. As an example, the TWI can use MT mode to write
data into a TWI EEPROM, MR mode to read the data back from the EEPROM. If other masters
are present in the system, some of these might transmit data to the TWI, and then SR mode
would be used. It is the application software that decides which modes are legal.
The following sections describe each of these modes. Possible status codes are described
along with figures detailing data transmission in each of the modes. These figures contain the
following abbreviations:
S: START condition
Rs: REPEATED START condition
R: Read bit (high level at SDA)
W: Write bit (low level at SDA)
A: Acknowledge bit (low level at SDA)
A: Not acknowledge bit (high level at SDA)
Data: 8-bit data byte
P: STOP condition
SLA: Slave Address
In Figure 19-12 on page 224 to Figure 19-18 on page 233, circles are used to indicate that the
TWINT Flag is set. The numbers in the circles show the status code held in TWSR, with the
prescaler bits masked to zero. At these points, actions must be taken by the application to con-
tinue or complete the TWI transfer. The TWI transfer is suspended until the TWINT Flag is
cleared by software.
When the TWINT Flag is set, the status code in TWSR is used to determine the appropriate soft-
ware action. For each status code, the required software action and details of the following serial
transfer are given in Table 19-2 on page 223 to Table 19-5 on page 232. Note that the prescaler
bits are masked to zero in these tables.
19.7.1
Master Transmitter Mode
In the Master Transmitter mode, a number of data bytes are transmitted to a Slave Receiver
(see Figure 19-11 on page 222). In order to enter a Master mode, a START condition must be
transmitted. The format of the following address packet determines whether Master Transmitter
or Master Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if
SLA+R is transmitted, MR mode is entered. All the status codes mentioned in this section
assume that the prescaler bits are zero or are masked to zero.
相关PDF资料
PDF描述
PIC12F635T-I/SN IC MCU FLASH 1KX14 8SOIC
PIC12F629-E/MF IC MCU CMOS 8BIT 1K FLASH 8-DFN
PIC16HV616-E/ML IC PIC MCU FLASH 2KX14 16QFN
W2L1YC683MAT1A CAP CER 0.068UF 16V 20% X7R 0508
PIC12LF1840-E/SN MCU 7KB FLASH 256B RAM XLP 8SOIC
相关代理商/技术参数
参数描述
PIC12F1822-I/MF 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F1822-I/P 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F1822-I/P 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC12F 32MHZ PDIP-8 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC12F, 32MHZ, PDIP-8
PIC12F1822-I/SN 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F1822-I/SN 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC12F 32 MHz 8-DIP 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC12F, 32 MHz, 8-SOIC