- 您现在的位置：买卖IC网 > PDF目录11613 > PIC12F1822-E/MF (Microchip Technology)MCU 8BIT 2K FLASH 8DFN PDF资料下载
参数资料
| 型号： | PIC12F1822-E/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 60/109页 |
| 文件大小： | 0K |
| 描述： | MCU 8BIT 2K FLASH 8DFN |
| 标准包装： | 120 |
| 系列： | PIC® XLP™ 12F |
| 核心处理器： | PIC |
| 芯体尺寸： | 8-位 |
| 速度： | 32MHz |
| 连通性： | I²C，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 6 |
| 程序存储器容量： | 3.5KB（2K x 14） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 256 x 8 |
| RAM 容量： | 128 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.8 V ~ 5.5 V |
| 数据转换器： | A/D 4x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页当前第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页
245
7674F–AVR–09/09
ATmega164P/324P/644P
If differential channels are selected, the differential gain stage amplifies the voltage difference
between the selected input channel pair by the selected gain factor. This amplified value then
becomes the analog input to the ADC. If single ended channels are used, the gain amplifier is
bypassed altogether.
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage reference and
input channel selections will not go into effect until ADEN is set. The ADC does not consume
power when ADEN is cleared, so it is recommended to switch off the ADC before entering power
saving sleep modes.
The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and
ADCL. By default, the result is presented right adjusted, but can optionally be presented left
adjusted by setting the ADLAR bit in ADMUX.
If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read
ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the Data
Registers belongs to the same conversion. Once ADCL is read, ADC access to Data Registers
is blocked. This means that if ADCL has been read, and a conversion completes before ADCH is
read, neither register is updated and the result from the conversion is lost. When ADCH is read,
ADC access to the ADCH and ADCL Registers is re-enabled.
The ADC has its own interrupt which can be triggered when a conversion completes. When ADC
access to the Data Registers is prohibited between reading of ADCH and ADCL, the interrupt
will trigger even if the result is lost.
21.4
Starting a Conversion
A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC.
This bit stays high as long as the conversion is in progress and will be cleared by hardware
when the conversion is completed. If a different data channel is selected while a conversion is in
progress, the ADC will finish the current conversion before performing the channel change.
Alternatively, a conversion can be triggered automatically by various sources. Auto Triggering is
enabled by setting the ADC Auto Trigger Enable bit, ADATE in ADCSRA. The trigger source is
selected by setting the ADC Trigger Select bits, ADTS in ADCSRB (see description of the ADTS
bits for a list of the trigger sources). When a positive edge occurs on the selected trigger signal,
the ADC prescaler is reset and a conversion is started. This provides a method of starting con-
versions at fixed intervals. If the trigger signal still is set when the conversion completes, a new
conversion will not be started. If another positive edge occurs on the trigger signal during con-
version, the edge will be ignored. Note that an Interrupt Flag will be set even if the specific
interrupt is disabled or the global interrupt enable bit in SREG is cleared. A conversion can thus
be triggered without causing an interrupt. However, the Interrupt Flag must be cleared in order to
trigger a new conversion at the next interrupt event.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12F635T-I/SN | IC MCU FLASH 1KX14 8SOIC |
| PIC12F629-E/MF | IC MCU CMOS 8BIT 1K FLASH 8-DFN |
| PIC16HV616-E/ML | IC PIC MCU FLASH 2KX14 16QFN |
| W2L1YC683MAT1A | CAP CER 0.068UF 16V 20% X7R 0508 |
| PIC12LF1840-E/SN | MCU 7KB FLASH 256B RAM XLP 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC12F1822-I/MF | 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12F1822-I/P | 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12F1822-I/P | 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC12F 32MHZ PDIP-8 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC12F, 32MHZ, PDIP-8 |
| PIC12F1822-I/SN | 功能描述:8位微控制器 -MCU 3.5KB 128B RAM 32MHz Int. Osc 6 I/0 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| PIC12F1822-I/SN | 制造商:Microchip Technology Inc 功能描述:IC 8BIT MCU PIC12F 32 MHz 8-DIP 制造商:Microchip Technology Inc 功能描述:IC, 8BIT MCU, PIC12F, 32 MHz, 8-SOIC |
发布紧急采购，3分钟左右您将得到回复。