收藏本站
参数资料
型号： PIC16F1508T-I/SS
厂商： Microchip Technology
文件页数： 39/123页
文件大小： 0K
描述： IC MCU 8BIT 7KB FLASH 20-SSOP
标准包装： 1,600
系列： PIC® XLP™ 16F
核心处理器： PIC
芯体尺寸： 8-位
速度： 20MHz
连通性： I²C，LIN，SPI，UART/USART
外围设备： 欠压检测/复位，POR，PWM，WDT
输入/输出数： 17
程序存储器容量： 7KB（4K x 14）
程序存储器类型： 闪存
RAM 容量： 256 x 8
电压 - 电源 (Vcc/Vdd)： 2.3 V ~ 5.5 V
数据转换器： A/D 12x10b，D/A 1x5b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 20-SSOP（0.209"，5.30mm 宽）
包装： 带卷 (TR)
Micrel, Inc.
KSZ8873MLLJ
September 2011
22
M9999-091911-1.8
LinkMD
Cable Diagnostics
KSZ8873MLLJ supports the LinkMD
. The LinkMD feature utilizes time domain reflectometry (TDR) to analyze the
cabling plant for common cabling problems such as open circuits, short circuits and impedance mismatches.
LinkMD
works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes
the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault. Internal
circuitry displays the TDR information in a user-readable digital format.
Note: Cable diagnostics are only valid for copper connections and do not support fiber optic operation.
Access
LinkMD
is initiated by accessing the PHY special control/status registers {26, 42} and the LinkMD result registers {27, 43}
for ports 1 and 2 respectively; and in conjunction with the port registers control 13 for ports 1and 2 respectively to disable
Auto MDI/MDIX.
Alternatively, the MIIM PHY registers 0 and 29 can be used for LinkMD
access.
Usage
The following is a sample procedure for using LinkMD
with registers {42,43,45} on port 2.
1. Disable auto MDI/MDI-X by writing a ‘1’ to register 45, bit [2] to enable manual control over the differential pair used to
transmit the LinkMD
pulse.
2. Start cable diagnostic test by writing a ‘1’ to register 42, bit [4]. This enable bit is self-clearing.
3. Wait (poll) for register 42, bit [4] to return a ‘0’, indicating cable diagnostic test is completed.
4. Read cable diagnostic test results in register 42, bits [6:5]. The results are as follows:
00 = normal condition (valid test)
01 = open condition detected in cable (valid test)
10 = short condition detected in cable (valid test)
11 = cable diagnostic test failed (invalid test)
The ‘11’ case, invalid test, occurs when the KSZ8873MLLJ is unable to shut down the link partner. In this instance,
the test is not run, since it would be impossible for the KSZ8873MLLJ to determine if the detected signal is a reflection
of the signal generated or a signal from another source.
5. Get distance to fault by concatenating register 42, bit [0] and register 43, bits [7:0]; and multiplying the result by a
constant of 0.4. The distance to the cable fault can be determined by the following formula:
D (distance to cable fault) = 0.4 x {(register 26, bit [0]),(register 27, bits [7:0])}
D (distance to cable fault) is expressed in meters.
Concatenated value of registers 42 and 43 is converted to decimal before multiplying by 0.4.
The constant (0.4) may be calibrated for different cabling conditions, including cables with a velocity of propagation
that varies significantly from the norm.
Functional Overview: Power Management
The KSZ8873MLLJ supports enhanced power management feature in low power state with energy detection to ensure
low-power dissipation during device idle periods. There are five operation modes under the power management function
which is controlled by two bits in Register 195 (0xC3) and one bit in Register 29 (0x1D),45(0x2D) as shown below:
Register 195 bit[1:0] = 00 Normal Operation Mode
Register 195 bit[1:0] = 01 Energy Detect Mode
Register 195 bit[1:0] = 10 Soft Power Down Mode
Register 195 bit[1:0] = 11 Power Saving Mode
Register 29,45 bit 3 =1 Port Based Power Down Mode
Table 3 indicates all internal function blocks status under four different power management operation modes.
相关PDF资料
PDF描述
PIC16HV610-E/P IC PIC MCU FLASH 1KX14 14DIP
PIC16HV616-I/ML IC PIC MCU FLASH 2KX14 16QFN
PIC16F1507T-I/ML IC MCU 8BIT 3.5KB FLASH 20QFN
PIC16LF1507T-I/ML IC MCU 8BIT 3.5KB FLASH 20QFN
D38999/20MJ24PA CONN RCPT 24POS WALL MNT W/PINS
相关代理商/技术参数
参数描述
PIC16F1509-E/ML 功能描述:8位微控制器 -MCU 14KB FLASH 512B RAM 18 I/O 10-BIT ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1509-E/P 功能描述:8位微控制器 -MCU 14KB FLASH 512B RAM 18 I/O 10-BIT ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1509-E/SO 功能描述:8位微控制器 -MCU 14KB FLASH 512B RAM 18 I/O 10-BIT ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1509-E/SS 功能描述:8位微控制器 -MCU 14KB FLASH 512B RAM 18 I/O 10-BIT ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F1509-I/ML 功能描述:8位微控制器 -MCU 14KB FLASH 512B RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*