收藏本站
参数资料
型号： PIC16F526T-I/SL
厂商： Microchip Technology
文件页数： 69/122页
文件大小： 0K
描述： IC PIC MCU FLASH 1KX12 14SOIC
标准包装： 2,600
系列： PIC® 16F
核心处理器： PIC
芯体尺寸： 8-位
速度： 20MHz
外围设备： POR，WDT
输入/输出数： 11
程序存储器容量： 1.5KB（1K x 12）
程序存储器类型： 闪存
RAM 容量： 67 x 8
电压 - 电源 (Vcc/Vdd)： 2 V ~ 5.5 V
数据转换器： A/D 3x8b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 14-SOIC（0.154"，3.90mm 宽）
包装： 带卷 (TR)
配用： ICE2000-ND - EMULATOR MPLAB-ICE 2000 POD
其它名称： PIC16F526T-I/SLTR
PIC18F2221/2321/4221/4321 FAMILY
DS39689F-page 50
2009 Microchip Technology Inc.
5.4
Brown-out Reset (BOR)
PIC18F2221/2321/4221/4321 family devices implement
a BOR circuit that provides the user with a number of
configuration and power-saving options. The BOR is
controlled by the BORV<1:0> and BOREN<1:0>
Configuration bits. There are a total of four BOR
configurations which are summarized in Table 5-1.
The BOR threshold is set by the BORV<1:0> bits. If BOR
is enabled (any values of BOREN<1:0>, except ‘00’),
any drop of VDD below VBOR (parameter D005) for
greater than TBOR (parameter 35) will reset the device.
A Reset may or may not occur if VDD falls below VBOR
for less than TBOR. The chip will remain in Brown-out
Reset until VDD rises above VBOR.
If the Power-up Timer is enabled, it will be invoked after
VDD rises above VBOR; it then will keep the chip in
Reset
for
an
additional
time
delay,
TPWRT
(parameter 33). If VDD drops below VBOR while the
Power-up Timer is running, the chip will go back into a
Brown-out Reset and the Power-up Timer will be
initialized. Once VDD rises above VBOR, the Power-up
Timer will execute the additional time delay.
BOR
and
the
Power-on
Timer
(PWRT)
are
independently configured. Enabling BOR Reset does
not automatically enable the PWRT.
5.4.1
SOFTWARE ENABLED BOR
When BOREN<1:0> = 01, the BOR can be enabled or
disabled by the user in software. This is done with the
control bit, SBOREN (RCON<6>). Setting SBOREN
enables the BOR to function as previously described.
Clearing SBOREN disables the BOR entirely. The
SBOREN bit operates only in this mode; otherwise it is
read as ‘0’.
Placing the BOR under software control gives the user
the additional flexibility of tailoring the application to its
environment without having to reprogram the device to
change BOR configuration. It also allows the user to
tailor device power consumption in software by elimi-
nating the incremental current that the BOR consumes.
While the BOR current is typically very small, it may
have some impact in low-power applications.
5.4.2
DETECTING BOR
When Brown-out Reset is enabled, the BOR bit always
resets to ‘0’ on any Brown-out Reset or Power-on
Reset event. This makes it difficult to determine if a
Brown-out Reset event has occurred just by reading
the state of BOR alone. A more reliable method is to
simultaneously check the state of both POR and BOR.
This assumes that the POR bit is reset to ‘1’ in software
immediately after any Power-on Reset event. If BOR is
‘0’ while POR is ‘1’, it can be reliably assumed that a
Brown-out Reset event has occurred.
5.4.3
DISABLING BOR IN SLEEP MODE
When BOREN<1:0> = 10, the BOR remains under
hardware
control
and
operates
as
previously
described. Whenever the device enters Sleep mode,
however, the BOR is automatically disabled. When the
device returns to any other operating mode, BOR is
automatically re-enabled.
This mode allows for applications to recover from
brown-out situations, while actively executing code,
when the device requires BOR protection the most. At
the same time, it saves additional power in Sleep mode
by eliminating the small incremental BOR current.
TABLE 5-1:
BOR CONFIGURATIONS
Note:
Even when BOR is under software control,
the Brown-out Reset voltage level is still
set by the BORV<1:0> Configuration bits.
It cannot be changed in software.
BOR Configuration
Status of
SBOREN
(RCON<6>)
BOR Operation
BOREN1
BOREN0
00
Unavailable BOR disabled; must be enabled by reprogramming the Configuration bits.
01
Available
BOR enabled in software; operation controlled by SBOREN.
10
Unavailable BOR enabled in hardware in Run and Idle modes, disabled during
Sleep mode.
11
Unavailable BOR enabled in hardware; must be disabled by reprogramming the
Configuration bits.
相关PDF资料
PDF描述
PIC12F510T-I/MC IC PIC MCU FLASH 1024X12 8DFN
PIC12F510-E/MS IC PIC MCU FLASH 1.5KB 8MSOP
D38999/26WJ19PC CONN PLUG 19POS STRAIGHT W/PINS
PIC10F206-I/MC IC PIC MCU FLASH 512X12 8DFN
D38999/26WJ19PB CONN PLUG 19POS STRAIGHT W/PINS
相关代理商/技术参数
参数描述
PIC16F527-E/ML 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 1.5KB FLASH 20QFN
PIC16F527-E/P 制造商:Microchip Technology 功能描述:MCU 8-bit PIC16 PIC RISC 1.5KB Flash 2.5V/3.3V/5V 20-Pin PDIP Tube 制造商:Microchip Technology Inc 功能描述:1.5KB FLASH PROGRAM, 64B FLASH DATA, 8MHZ INTERNAL OSCILLATO - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 1.5KB FLASH 20PDIP 制造商:Microchip Technology Inc 功能描述:8-bit Microcontrollers - MCU 8MHz Oscillator, 8b ADC 2x Comp, 2x Amps
PIC16F527-E/SO 制造商:Microchip Technology Inc 功能描述:1.5KB FLASH PROGRAM, 64B FLASH DATA, 8MHZ INTERNAL OSCILLATO - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 1.5KB FLASH 20SOIC
PIC16F527-I/ML 功能描述:8位微控制器 -MCU 8MHz Oscillator, 8b ADC 2x Comp, 2x Amps RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC16F527-I/P 功能描述:8位微控制器 -MCU 8MHz Oscillator, 8b ADC 2x Comp, 2x Amps RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*